Key takeaways
- Average the bases, then multiply by height. A = ½(a + b)h, or mh.
- Height is perpendicular. A slanted leg is always longer than the height between the bases.
- The median is the average. It runs between the legs’ midpoints and equals ½(a + b).
- Parallelograms are trapezoids under the inclusive definition, and the formula still works.
- Units must match. Area comes out in square units, not the unit of the sides.
What counts as a trapezoid
In US usage, a trapezoid is a quadrilateral with at least one pair of parallel sides. The parallel sides are the bases, usually written a and b, and the other two sides are the legs. The perpendicular distance between the bases is the height h. British usage swaps the words: the same shape is called a trapezium, while “trapezoid” refers to a quadrilateral with no parallel sides. When a problem uses either word, confirm the definition before applying a formula.
There are two competing definitions. The inclusive definition counts any quadrilateral with at least one pair of parallel sides, which makes parallelograms, rectangles, and squares special trapezoids. The exclusive definition requires exactly one pair, which excludes those shapes. The area formula works under both, because setting a = b for a parallelogram reduces it to base times height.
Why the area formula works
Take two congruent copies of the trapezoid and rotate one by 180 degrees. Joined along a leg, they form a parallelogram whose base is a + b and whose height is h. The parallelogram’s area is (a + b)h, so one trapezoid has half of that: A = ½(a + b)h. This is the same “average of the parallel sides times height” rule used for the trapezoidal rule in numerical integration.
A second proof decomposes the shape. Drop perpendiculars from the top base to the bottom base. The middle region is a rectangle of width a and height h, and the two outer regions are triangles with heights h and horizontal bases that add up to b − a. Their combined area is ½(b − a)h, and the rectangle is ah, so the total is ah + ½(b − a)h = ½(a + b)h. Both proofs assume the height is measured perpendicular to the bases.
Median and the area shortcut
The median, also called the midline, joins the midpoints of the two legs. It is parallel to the bases and its length is the average of the bases: m = ½(a + b). The area can then be written as A = mh, which is often easier to remember and to use when the median is measured directly. For bases 6 and 10, the median is 8; with height 4, the area is 8 × 4 = 32.
The median is a length, not an area, and it lies inside the trapezoid. Its distance from each base is half the height, so it is a useful reference line for centring a label or checking a drawing. In a parallelogram, the median equals the base, which is another way to see why A = mh generalizes the parallelogram formula.
Height is perpendicular, not the leg
The single most common error is using a slanted leg as the height. In a right trapezoid, one leg is perpendicular to the bases, so that leg equals the height. In every other trapezoid, the leg is longer than the height because it is the hypotenuse of a right triangle whose vertical leg is h. Using the leg inflates the area by the ratio of leg to height.
To find the height from a leg, you need an angle or the horizontal offset. In an isosceles trapezoid with bases a and b, each side offset is ½(b − a). If the leg has length c, the height is h = √(c² − (½(b − a))²). For bases 6 and 10 and leg 5, the offset is 2, so h = √(25 − 4) = √21 ≈ 4.58. Without the offset or an angle, the height is not determined by the bases and leg alone.
Worked example: bases 6 and 10, height 4
A = ½(6 + 10) × 4 = ½ × 16 × 4 = 32 square units. The median is ½(6 + 10) = 8, and 8 × 4 = 32 confirms the shortcut. The decomposition also checks: the central rectangle is 6 × 4 = 24, and the two end triangles each have base 2 and height 4, so each is ½ × 2 × 4 = 4. Total 24 + 4 + 4 = 32.
Keep the units straight. If the bases and height are in metres, the area is in square metres. If the bases are in feet and the height in inches, convert first: 6 ft and 10 ft with a height of 24 in becomes h = 2 ft, so A = ½(16)(2) = 16 ft². Multiplying 16 by 24 without converting would give 192, which is not a meaningful area in either unit.
Finding a missing base or height
Rearrange the formula as needed. Height: h = 2A ÷ (a + b). One base: a = 2A ÷ h − b. For example, an area of 45 with bases 6 and 12 gives h = 90 ÷ 18 = 5. An area of 32 with height 4 and bottom base 10 gives a = 64 ÷ 4 − 10 = 6. These rearrangements are exact; only the final division introduces rounding.
If you know the area and the median, the height is simply h = A ÷ m. If you know the area and height but not either base individually, you can only recover their sum, not the split. That is a real limitation: many pairs of bases have the same average. A drawing or an additional measurement is needed to separate them.
Isosceles trapezoids: legs, diagonals, and angles
An isosceles trapezoid has equal legs and equal base angles at each base. Its diagonals are also equal. With bases 6 and 10 and height 4, each side offset is (10 − 6) ÷ 2 = 2, so the leg is √(4² + 2²) = √20 ≈ 4.47. The diagonal runs from a bottom corner to the opposite top corner: its horizontal run is 10 − 2 = 8, so its length is √(8² + 4²) = √80 ≈ 8.94. In general, an isosceles trapezoid’s diagonal is √(h² + m²), where m is the median.
Base angles come from the same triangle. The acute angle at the bottom base satisfies tan θ = h ÷ offset = 4 ÷ 2 = 2, so θ ≈ 63.43°. The angle at the top base is its supplement, about 116.57°.
Units and practical applications
Trapezoids appear in land plots, road cross-sections, roof sections, and any shape with two parallel edges of different lengths. The area rule also underlies the trapezoidal rule for estimating the area under a curve: divide the span into strips, treat each strip as a trapezoid, and add the areas. For a prism with a trapezoidal cross-section, volume is the cross-sectional area times the length, so a 32 m² section extruded 5 m gives 160 m³.
Measure the perpendicular height, not the slope length along the face. On a plot, that may mean measuring offsets at right angles to a baseline rather than pacing along the boundary. Keep every measurement in one unit before calculating, and report area in square units.
Common mistakes
- Using a slanted leg as the height, which overstates the area.
- Forgetting the factor of ½ and reporting (a + b)h.
- Averaging all four sides instead of only the two parallel bases.
- Adding the bases but using the difference in the height calculation.
- Assuming every trapezoid is isosceles, so the legs and diagonals are not actually equal.
- Mixing units, such as bases in feet and height in inches.
Trapezoid, trapezium, and parallelogram
The naming differs by region. In the United States, a trapezoid has at least one pair of parallel sides, and a trapezium has none. In the United Kingdom, the trapezium has one pair of parallel sides, and the trapezoid has none. MathWorld notes the same transatlantic swap. Neither convention changes the mathematics; it changes which word a textbook uses for the shape.
Under the inclusive definition, a parallelogram is a trapezoid with a = b. Then A = ½(a + a)h = ah, the familiar base-times-height rule. A rectangle adds right angles, and a square adds equal sides.
Frequently asked questions
What is the trapezoid area formula?
A = ½(a + b)h, where a and b are the parallel bases and h is the perpendicular height. Equivalently, A = mh with m = ½(a + b).
Is the height the same as a leg?
Only in a right trapezoid, where one leg is perpendicular to the bases. In every other trapezoid the leg is longer than the height.
How do I find the height from the area?
Rearrange to h = 2A ÷ (a + b). For A = 45 and bases 6 and 12, h = 90 ÷ 18 = 5.
What is the median of a trapezoid?
The segment joining the midpoints of the legs. It is parallel to the bases and has length ½(a + b).
Can a trapezoid have two pairs of parallel sides?
Yes, under the inclusive definition; that shape is a parallelogram. Under the exclusive definition, a trapezoid has exactly one pair.
Why is my area twice what I expected?
You probably omitted the ½. The formula averages the bases before multiplying by height, so (a + b)h is twice the area.
Further reading