What this calculator does
Baseboard trim is sold in fixed lengths, and the quantity that matters is not just the perimeter. Doors, archways, fireplaces, and built-ins interrupt the run, while inside and outside corners create offcuts that cannot always be used. This calculator starts with the room perimeter, subtracts the openings, adds a waste allowance, and divides by the stock length. It gives a material estimate for a simple rectangular room. Closets, bay windows, stair returns, and rooms with many corners need a measured takeoff or a larger allowance.
How to use it
- Measure the room length and width in metres.
- Count the doors and enter the width of each.
- Add any other openings where the baseboard stops.
- Choose the stock length you plan to buy.
- Add a waste allowance for corners, cuts, and defects.
How it works
Example calculations
Example 1: 5 × 4 m room, two 0.9 m doors
The perimeter is 18.0 m. Two doors remove 1.8 m, leaving 16.2 m. With 10% waste, buy 17.82 m, or 8 pieces at 2.4 m.
Example 2: 6 × 5 m room, three doors and a 2 m opening
The perimeter is 22.0 m. The doors and opening remove 4.7 m, leaving 17.3 m. With 10% waste and 3.0 m stock, the order is 19.03 m, or 7 pieces.
Example 3: 3.5 × 3 m room, one door, 15% waste
The perimeter is 13.0 m and the door removes 0.9 m. A 15% waste allowance brings the order to 13.92 m. At 2.4 m stock, that is 6 pieces.
What the result means
The perimeter method works for a simple rectangular room, but it underestimates rooms with closets, bay windows, or many corners. Waste is not just breakage: a 3.6 m wall cannot be covered by a single 2.4 m piece without a joint, and a joint in the middle of a wall is visible. Buying longer stock can reduce joints and waste, while short stock can be cheaper but leave more offcuts. The calculator does not include baseboard height, profile, or adhesive and nails. For a finished look, plan the joints over doorways or in inconspicuous corners and keep a spare piece for repairs.
Common mistakes
- Using the room area instead of the perimeter.
- Forgetting to subtract doors and other openings.
- Ordering exact lengths with no allowance for corners and defects.
- Ignoring the joint layout and ending up with a seam in a prominent spot.
- Buying short stock that cannot span a long wall without a joint.
Assumptions and limits
- The room is a simple rectangle with four walls.
- Each door opening removes its full width from the baseboard run.
- Other openings are entered as a total length.
- Stock is cut with normal carpentry waste, not a complex profile.
- No closets, bay windows, stairs, or cabinetry are included.
Frequently asked questions
How much extra baseboard should I buy?
Ten percent is a common allowance for a simple room. Add more for rooms with many corners, closets, or a pattern that requires long pieces. Keep at least one spare piece for future repairs.
Do I subtract doors from the perimeter?
Yes, baseboard stops at a door casing, so subtract the door width or the casing-to-casing opening. Do not subtract windows unless the baseboard is interrupted there.
Should I use 2.4 m or 3.6 m stock?
Longer stock reduces joints and can be faster to install, but it costs more and is harder to handle in tight spaces. Short stock is easier to transport but creates more offcuts and visible seams.
How do I handle inside and outside corners?
Inside corners are usually coped or mitered; outside corners are mitered. Both create offcuts, which is why the waste allowance matters. Test the fit before nailing.
Does baseboard height affect the quantity?
Not the length, but a taller baseboard has more visible joints and may need longer stock. The calculator works in linear metres, so height does not change the perimeter.
What about closets and bay windows?
Measure each additional run and add it to the total. The simple perimeter formula will underestimate those spaces. For a complex room, measure wall by wall and add the lengths.
Sources
2026 update
How to use the professional output
This page is not just a formula box. The result is designed to be checked, compared, and taken away.
- Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
- A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
- Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.
The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.