What this calculator does
Siding estimates fail in two directions: too few panels and the job stops, too many and the money sits in the garage. The reliable method is to calculate the wall area, subtract doors and windows, add a waste allowance for cuts and corners, and divide by the coverage of one panel or board. This calculator does that and rounds up to whole units. It works for vinyl, fibre cement, wood, and composite siding as long as you enter the coverage printed on the product. It does not include trim, house wrap, fasteners, or the starter strip, and it assumes a simple rectangular wall.
How to use it
- Measure the wall length and height in metres.
- Add up the area of doors and windows to subtract.
- Enter the coverage of one panel or board from the product data.
- Choose a waste allowance, typically 10% for a simple wall and more for complex shapes.
- Round the result up and add separate trim and accessory quantities.
How it works
Example calculations
Example 1: 12 m x 2.7 m wall with 4 m虏 of openings
Gross area is 32.4 m虏, net area is 28.4 m虏, and with 10% waste you need 31.2 m虏 of siding. At 0.72 m虏 per panel, that rounds up to 44 panels.
Example 2: Small wall with 15% waste
An 8 m x 2.4 m wall has 19.2 m虏 gross and 16.7 m虏 net after 2.5 m虏 of openings. With 15% waste the required area is 19.21 m虏, which is 27 panels at 0.72 m虏 each.
Example 3: Larger 1.44 m虏 panels
Using the same default wall but a 1.44 m虏 panel, the required area of 31.24 m虏 needs 22 panels. Larger panels reduce the count but are heavier and may waste more on short walls.
What the result means
The coverage figure is the key input. For lap siding, the effective coverage is the exposed face height, not the full board width, so use the manufacturer's stated coverage rather than measuring the board. Complex walls with gables, dormers, and many corners need a higher waste allowance. The estimate also assumes the panels can be cut efficiently; a small wall may need an extra panel even if the arithmetic says otherwise. Keep one spare panel for future repairs, especially with a discontinued colour.
Common mistakes
- Using the full board width instead of the exposed coverage for lap siding.
- Forgetting to subtract doors and windows.
- Using a 5% waste allowance on a wall with many corners and gables.
- Mixing square metres and square feet in the same calculation.
- Leaving out trim, corner pieces, and fasteners from the order.
Assumptions and limits
- The wall is a simple rectangle with the stated openings.
- Coverage per panel is the effective installed coverage.
- Waste covers normal cuts, corners, and minor damage.
- The panel layout can use offcuts efficiently.
- Trim, wrap, and fasteners are ordered separately.
Frequently asked questions
How much waste should I add for siding?
About 10% is common for a simple rectangular wall. Use 15% or more for gables, dormers, many corners, or a diagonal layout. Keep at least one spare panel for repairs.
Do I subtract windows and doors?
Yes. Subtract the rough opening area or the actual opening area, depending on how the siding will be trimmed. The calculator uses the area you enter.
What coverage do I enter for lap siding?
Use the exposed face coverage, not the full board width. The manufacturer's data sheet gives the coverage per piece or per square, and that is the number to use.
Does the calculator include trim and corners?
No. Corner posts, starter strips, J-channel, fascia, and fasteners are separate. Measure the perimeter and openings for trim after you settle the siding quantity.
Can I use this for a gable wall?
Calculate the rectangular part and the triangular gable separately, then add them. Increase the waste allowance because the gable produces angled cuts.
Why did the calculator round up so much?
It rounds up to whole panels, and the leftover is the spare coverage shown in the results. A fractional panel cannot be bought, so rounding up is the safe approach.
Sources
2026 update
How to use the professional output
This page is not just a formula box. The result is designed to be checked, compared, and taken away.
- Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
- A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
- Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.
The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.