Skip to content

Annulus Calculator

Enter the outer and inner diameters. The annulus area is π × (R² - r²), where R and r are the two radii. An outer diameter of 1.2 m and an inner diameter of 0.8 m give an area of about 0.6283 m² and a ring width of 0.2 m.

Updated 2026-11-19 Editorial estimate Calccc Editorial Team Free · No sign-up
m
m
Scenarios A/BSave two input sets and compare the results. Stored only in this browser.
AEmpty
BEmpty

Your inputs stay in this browser. No account, no uploads.

Professional worksheet

Detailed schedule & assumptions

Inputs used, method, sensitivity, and any year-by-year table. The summary above stays compact; the audit lives here.

Professional worksheet

Inputs, scope, and sensitivity

Inputs used

Method and scope

Result audit

MetricValue

What this calculator does

An annulus is the flat ring between two concentric circles: a washer, a gasket, a circular path, or the cross-section of a pipe. Its area is the difference between the outer circle and the inner circle, which is π × (R² - r²). The shape is simple, but the diameters are often what you can measure, so the calculator converts them to radii and reports the area, the ring width, both circumferences, and the mean diameter. It also shows what share of the outer circle the hole removes. Use it for material estimates, gasket sizing, and geometry checks where the ring is circular and the two circles share a centre.

How to use it

  1. Measure the outer diameter across the widest part of the ring.
  2. Measure the inner diameter across the hole.
  3. Enter both values in the same unit, such as metres or centimetres.
  4. Read the annulus area and the ring width.
  5. Use the circumferences for edge length or sealing estimates.
  6. Check that the inner diameter is smaller than the outer diameter.

How it works

Outer radius R = outer diameter / 2. Inner radius r = inner diameter / 2. Annulus area = π × (R² - r²). Ring width = R - r. Outer circumference = 2πR. Inner circumference = 2πr. Mean diameter = (outer diameter + inner diameter) / 2.

Example calculations

Example 1: A 1.2 m outer and 0.8 m inner diameter

The outer radius is 0.6 m and the inner radius is 0.4 m. The annulus area is π × (0.36 - 0.16) = 0.6283 m². The ring width is 0.2 m, the outer circumference is 3.7699 m, and the inner circumference is 2.5133 m. The hole removes 44.4% of the outer circle's area.

Example 2: A 2 m outer and 1 m inner diameter

The radii are 1 m and 0.5 m. The area is π × (1 - 0.25) = 2.3562 m². The ring width is 0.5 m, and the mean diameter is 1.5 m. The hole removes 25% of the outer area because the inner radius is half the outer radius.

Example 3: A thin 0.5 m ring

An outer diameter of 0.5 m and an inner diameter of 0.45 m give radii of 0.25 m and 0.225 m. The area is only about 0.0373 m², and the ring width is 0.025 m, or 25 mm. The hole removes 81% of the outer area, which is why a thin ring can have a small area even though its outside diameter looks substantial.

What the result means

The area is the material area of the ring, not the area of the hole or the outer circle. The ring width is the radial thickness, which is often the critical dimension for a gasket or a washer. The mean diameter is a convenient single number for ordering or comparing rings, but it is not the diameter at which the area is exactly half; the area-weighted mean radius is different. The removed percentage shows how much of the outer circle is empty. Keep both diameters in the same unit: mixing metres and centimetres will produce an area that is off by a factor of 10,000.

Common mistakes

  • Using diameters in the area formula instead of radii.
  • Mixing units between the inner and outer diameter.
  • Subtracting the circumferences instead of the areas.
  • Using the mean diameter as if it were the radius.
  • Assuming the two circles are concentric when they are offset.
  • Confusing the annulus area with the area of the hole.

Assumptions and limits

  • The inner and outer circles are concentric.
  • Both diameters are measured in the same unit.
  • The ring is flat and has a uniform width.
  • The inner diameter is smaller than the outer diameter.
  • No thickness or depth is included; the result is a two-dimensional area.
  • The shape is a true circle, not an ellipse or an irregular ring.

Frequently asked questions

What is an annulus?

It is the region between two concentric circles, like a ring or a washer. Its area is the outer circle's area minus the inner circle's area.

Why not use the average diameter to find the area?

The area depends on the squares of the radii, not on the average diameter. Using the mean diameter as a radius would give the wrong result. The correct formula is π × (R² - r²).

What is the ring width?

It is the difference between the outer and inner radii, which is also half the difference between the outer and inner diameters. In the default example it is 0.2 m.

Can I use this for a pipe cross-section?

Yes, if the pipe is circular and concentric. The annulus area is the material area of the wall. For a full three-dimensional volume, multiply the area by the pipe length.

What if the circles are not concentric?

Then the shape is not a true annulus and this formula does not apply. The area would need the offset between the centres and a more general calculation.

What units should I use?

Any consistent length unit. The area is reported in that unit squared. If you enter centimetres, the area is in square centimetres; if you enter metres, it is in square metres.

Sources

This calculator is an educational planning tool, not financial, legal, insurance, medical, or professional advice. Results depend on the inputs and on rules that vary by place and provider. Confirm important decisions with a qualified professional and the relevant documents.

2026 update

How to use the professional output

This page is not just a formula box. The result is designed to be checked, compared, and taken away.

  • Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
  • A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
  • Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.

The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.

Calccc Editorial Team · Updated 2026-11-19

Prepared by Calccc Editorial Team as an educational estimate. This page is not a licensed professional review and is not financial, medical, legal, or tax advice.

Editorial estimate prepared by the Calccc Editorial Team; not a licensed professional review.