What this calculator does
A frustum is the shape left when the top of a cone or pyramid is cut off parallel to the base. Buckets, planters, lampshades, funnels, and tapered containers are all frustums, and so are the tapered sections of some ducting and moulds. Its volume is not the average of the two circular areas times the height, which is a common mistake: because the radius changes linearly, the volume formula includes the product of the two radii as well as their squares. The result sits between the volume of a cylinder with the smaller radius and one with the larger radius, closer to the larger one. The slant height is the straight-line distance along the side, not the vertical height, and the lateral surface area uses the slant height rather than the height. This calculator handles those distinctions and returns volumes in both cubic centimetres and litres, which is useful when a container's capacity matters more than its geometry.
How to use it
- Enter the radius of the larger base at the bottom.
- Enter the radius of the smaller base at the top.
- Enter the vertical height between the two parallel bases.
- Read the volume in cubic centimetres and litres.
- Check the slant height before cutting a side panel or a template.
- Use the total surface area for material estimates, and the lateral area if the bases are not covered.
How it works
Example calculations
Example 1: A tapered bucket
A bucket with a bottom radius of 10 cm, a top radius of 12 cm, and a height of 30 cm has a volume of pi × 30 / 3 × (144 + 120 + 100) = 11,435 cm3, or about 11.4 L. The slant height is the square root of 900 + 4 = 30.07 cm, and the lateral area is pi × 22 × 30.07 = 2,078 cm2. That is the area of the side wall, before adding the base if the bucket has one.
Example 2: A planter
A planter with a bottom radius of 15 cm, a top radius of 20 cm, and a height of 40 cm holds pi × 40 / 3 × (400 + 300 + 225) = 38,746 cm3, or about 38.7 L of soil. A bag of potting mix sold by volume can be compared directly with that figure, but the planter is not filled to the rim, so a realistic fill is usually 10% to 15% less.
Example 3: The cone special case
A cone is a frustum with a top radius of zero. With R = 10, r = 0, and height = 12, the formula gives pi × 12 / 3 × 100 = 1,257 cm3, or 1.26 L, which is exactly one third of the cylinder with the same base and height. This is a useful check: the frustum formula reduces to the cone formula when the top radius vanishes, and to the cylinder formula when the two radii are equal.
What the result means
The volume tells you capacity, and the surface area tells you material. For a container, the capacity is the volume up to the fill line, not to the rim, so allow some freeboard. For a template or a wrap, the lateral area and the slant height are the useful numbers, because the side of a frustum unrolls into a sector of an annulus rather than a rectangle. The formula assumes a right circular frustum with parallel flat bases. If the top and bottom are not parallel, or if the shape is elliptical, the result is an approximation. If the walls have thickness, the external dimensions give the outside volume, and the internal capacity is smaller by the wall thickness on every radius.
Common mistakes
- Averaging the two base areas and multiplying by the height instead of using the correct formula.
- Using the vertical height as the slant height for the lateral area.
- Forgetting to add the base and top areas when the total surface area is needed.
- Mixing diameters and radii in the same calculation.
- Mixing units, such as a radius in centimetres and a height in metres.
- Assuming the volume is the container's usable capacity without allowing for freeboard or wall thickness.
Assumptions and limits
- The shape is a right circular frustum.
- The top and bottom bases are parallel and flat.
- The radii are measured to the inside surface if capacity is being calculated.
- The height is the perpendicular distance between the bases.
- The walls have negligible thickness unless stated otherwise.
- The material is uniform and the shape is not deformed.
Frequently asked questions
What is a frustum?
A frustum is the part of a cone or pyramid that remains when the top is cut off by a plane parallel to the base. A bucket and a lampshade are familiar examples.
How is frustum volume different from cone volume?
A cone has a single radius, while a frustum has two. The frustum formula includes both radii and their product, so it reduces to the cone formula when the top radius is zero and to the cylinder formula when the two radii are equal.
What is slant height?
It is the distance along the slanted side from the bottom edge to the top edge. It is longer than the vertical height, and it is the length used for the lateral surface area and for laying out a side template.
Can I use diameters instead of radii?
Yes, if you halve them first. The formula uses radii, so using diameters without converting gives a volume that is four times too large. Convert the diameters to radii before entering the values.
Does the formula work for a pyramid frustum?
Not directly. A conical frustum uses pi and circular bases, while a pyramid frustum uses the areas of its polygonal bases. The same idea applies, but the constants and the base-area terms are different.
Why is the volume larger than the average of the two cylinders?
Because the radius changes linearly but the area changes with the square of the radius, the middle of the shape has more volume than a straight average would suggest. The R × r term in the formula captures that effect.
Sources
2026 update
How to use the professional output
This page is not just a formula box. The result is designed to be checked, compared, and taken away.
- Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
- A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
- Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.
The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.