The short answer: torque is force times lever arm, and the SI unit is the newton-metre: 1 N·m = 1 N × 1 m. The US customary unit is the pound-foot, and 1 lb-ft = 1.3558179483314004 N·m exactly under standard gravity, so 1 N·m = 0.7375621493 lb-ft. That makes 100 N·m = 73.756 lb-ft and 50 lb-ft = 67.791 N·m. Inch-pounds are 1/12 of a pound-foot: 1 in-lb = 0.1129848290 N·m. Kilogram-force metres are 9.80665 N·m.

Key takeaways

  • Torque is force times perpendicular distance. The newton-metre is the coherent SI unit.
  • 1 lb-ft = 1.3558179483 N·m exactly, from the exact definitions of the pound, foot, and standard gravity.
  • 1 N·m = 0.7375621493 lb-ft. A 100 N·m specification is only 73.76 lb-ft.
  • 1 in-lb = 0.112984829 N·m, and 12 in-lb make one lb-ft.
  • Torque and energy share dimensions but not meaning. The lb-ft versus ft-lb label is a real trap.

Torque is a moment about an axis

Torque measures the turning effect of a force. For a force applied perpendicular to a lever arm, τ = r × F, where r is the distance from the pivot and F is the force. A 200 N force at the end of a 0.5 m wrench produces 100 N·m. Doubling either the force or the arm doubles the torque; applying the force at an angle reduces the effective component to F sin θ, where θ is the angle between the force and the arm.

The direction matters too. Torque is a vector along the axis of rotation, and a sign convention distinguishes clockwise from counterclockwise. For tightening a fastener, the magnitude is usually what the specification states, but the sign should be kept in dynamic problems. The units describe the same physical quantity whether the arm is a wrench, a shaft, or a lever.

The newton-metre is the SI unit

One newton-metre is the torque from one newton applied one metre from the pivot, perpendicular to the arm. Because the newton and the metre are coherent SI units, no conversion factor appears in the definition. The unit is written N·m; the order of the factors does not change the value, and the middle dot separates the two unit symbols.

The newton-metre is also dimensionally a joule, because 1 N × 1 m = 1 J. That equivalence is a bookkeeping fact, not a statement that torque and energy are the same. Energy is a scalar and describes work done; torque is a vector and describes a turning effect. Keeping the unit labels distinct — N·m for torque, J for energy — preserves that distinction in calculations.

Pound-foot and its exact factor

The pound-foot uses the pound-force and the foot: 1 lbf = 0.45359237 kg × 9.80665 m/s² = 4.4482216152605 N, and 1 ft = 0.3048 m. Multiply them and 1 lb-ft = 1.3558179483314004 N·m. The pound and foot are defined exactly in SI, and standard gravity is an exact conventional value, so the factor is exact under those definitions rather than a measured approximation.

The inverse is 1 / 1.3558179483314004 = 0.7375621493 lb-ft per N·m. NIST lists the factor rounded to 1.355818, which is sufficient for most engineering work but not for a chain of calculations that needs full precision. Using 1.356 is convenient in the shop and introduces an error of about 0.013%, which is negligible next to wrench accuracy.

Worked conversions

100 N·m to lb-ft. 100 / 1.3558179483 = 73.7562 lb-ft. Rounded to one decimal, 73.8 lb-ft.

50 lb-ft to N·m. 50 × 1.3558179483 = 67.7909 N·m. The newton-metre value is larger than the pound-foot number because one pound-foot is a larger unit.

8 lb-ft to N·m. 8 × 1.3558179483 = 10.8465 N·m. Small fastener specifications are often written in inch-pounds instead: 96 in-lb is the same torque.

200 N·m to lb-ft. 200 / 1.3558179483 = 147.512 lb-ft. Doubling the input doubles the output, so the factor is unchanged.

150 lb-ft to N·m. 150 × 1.3558179483 = 203.373 N·m. A common wheel-nut range in one unit can look very different in the other.

Inch-pounds, kgf·m, and other units

One inch-pound is one twelfth of a pound-foot: 0.1129848290 N·m. The unit is common on small fasteners, bicycle components, and instrument screws, where a pound-foot value would have too few significant digits. Twelve inch-pounds make one pound-foot, so a 90 in-lb specification is 7.5 lb-ft or 10.17 N·m.

The kilogram-force metre is 9.80665 N·m, and the kilogram-force centimetre is 0.0980665 N·m. These units appear in older metric manuals and in some Asian equipment. The newton-centimetre is 0.01 N·m. When a manual mixes kgf·m with N·m, convert both to N·m before comparing; the numbers differ by roughly a factor of ten, which is large enough to damage a fastener.

Torque is not power

Power is torque multiplied by angular speed. In US customary units, horsepower = torque in lb-ft × rpm / 5,252. In SI, power in kW = torque in N·m × rpm / 9,549. An engine can make high torque at low rpm and low torque at high rpm; the power curve combines both. That is why a diesel and a petrol engine with similar peak torque can have very different power ratings.

The constant 5,252 comes from 33,000 ft·lb/min divided by 2π. The SI constant 9,549 comes from 60,000 / 2π. Neither is a conversion factor between torque units; they convert a torque-and-speed product into power. Mixing lb-ft with rpm in the SI formula, or N·m with rpm in the US formula, gives a meaningless number.

Reading fastener specs and wrench markings

A torque wrench is marked in one unit, and the specification may be in another. Convert the specification into the wrench’s unit, not the other way around, and then set the wrench. A fastener specified at 100 N·m needs 73.8 lb-ft on a pound-foot wrench. Setting 100 lb-ft applies about 135.6 N·m, roughly 36% too much, which can stretch or snap the fastener.

Extensions and adapters change the effective lever arm. A crow’s-foot or an extension used at an angle requires a correction that depends on the geometry; a straight extension in line with the wrench does not change the torque at the fastener in theory, but it does add compliance and friction. Lubrication, thread condition, and torque angle also change the clamp load for the same torque. Follow the manufacturer’s procedure rather than treating the converted number as a complete instruction.

Common mistakes

Confusing lb-ft with ft-lb. The abbreviations are often used loosely, but torque is conventionally lb-ft and energy ft-lb. The dimensions are the same, the physical quantity is not.

Using the wrong direction. To go from N·m to lb-ft, divide by 1.3558; to go from lb-ft to N·m, multiply. Reversing the operation changes the answer by a factor of 1.84.

Mixing inch-pounds and pound-feet. The factor is 12, so 100 in-lb is 8.33 lb-ft, not 100 lb-ft. Small-fastener specs are especially prone to this.

Rounding the factor too early. Using 1.36 instead of 1.3558 is fine for a shop estimate but accumulates error in a multi-step calculation. Keep full precision until the final display.

Treating the setting as the applied torque. Wrench accuracy, extension geometry, friction, and thread condition all affect the actual clamp load. A conversion does not calibrate the tool.

Rounding, tolerance, and calibration

The conversion factor is exact, but the torque value is not. A specification of 100 N·m is usually a nominal value with a tolerance, such as ±5%. Convert the tolerance with the same factor: 5 N·m is 3.69 lb-ft, so the range becomes about 70.1–77.5 lb-ft. Re-rounding the nominal value and guessing the band loses that information.

For workshop use, three significant figures are enough: 100 N·m = 73.8 lb-ft. For engineering analysis, carry at least six. Torque wrench accuracy is typically ±2% to ±4% of the reading, which is larger than the rounding error in the conversion. The converter uses 1.3558179483314, a 14-digit approximation of the exact factor; the difference appears far beyond the precision of any wrench.

Frequently asked questions

How many newton-metres are in one pound-foot?

1.3558179483 N·m. Multiply a pound-foot value by that factor. For example, 50 lb-ft = 67.791 N·m.

How many pound-feet are in one newton-metre?

0.7375621493 lb-ft. Divide a newton-metre value by 1.3558179483, or multiply by 0.7375621493.

Is lb-ft the same as ft-lb?

The abbreviations are often used interchangeably, but torque is usually written lb-ft and energy ft-lb. They share dimensions but describe different quantities, so read the context and the unit label.

How do I convert inch-pounds to newton-metres?

Multiply by 0.1129848290. So 90 in-lb = 10.17 N·m, and 12 in-lb = 1 lb-ft = 1.3558 N·m.

Why is 100 N·m not 100 lb-ft?

Because one pound-foot is larger than one newton-metre. 100 N·m is 73.76 lb-ft; using 100 lb-ft would apply about 135.6 N·m, roughly 36% too much.

Does an extension change the torque at the fastener?

A straight extension in line with the wrench does not change the theoretical torque, but it adds compliance and friction. An offset adapter such as a crow’s-foot changes the lever arm and needs a correction. Follow the tool maker’s procedure.

Further reading

Keep exploring

Read next Hex to RGB: Color Codes, Channels, and Alpha A hex code is three base-16 channel values in one string. Learn how RR, GG, and BB become… Read next Density Conversion: kg/m³, g/cm³, and lb/ft³ Density is mass per volume, and the metric and imperial units are linked by exact factors. Learn the… Read next Base Conversion: Binary, Decimal, Hex, and Place Value Convert integers between binary, octal, decimal, and hexadecimal, with place-value arithmetic, direct bit grouping, exact limits, and the…