What this calculator does
A fence takeoff looks simple until the gates and the ends are counted properly. Posts do not follow the panel count one for one: a straight run needs a post at each end and one at every spacing interval, and every gate opening needs two heavier gate posts. That is why a 40 m run at 2.4 m spacing needs 18 line posts, not 16. The concrete figure is a separate estimate driven by hole diameter and depth, so the bag count is only as good as the hole you actually dig. This page states the formula, the metric defaults, and the waste assumption so you can check the order against your own plan.
How to use it
- Measure the total fence run in metres, including the width of any gate openings.
- Enter the post spacing measured from centre to centre. 2.4 m is a common panel spacing.
- Enter the number of gates. Each gate adds two gate posts.
- Set the concrete bags per post. The default of two 20 kg bags suits a 200 mm × 600 mm hole.
- Add a waste allowance for breakage and miscuts, then review the post and bag counts.
How it works
Example calculations
Example 1: 40 m run, 2.4 m spacing, one gate
40 ÷ 2.4 = 16.67, rounded up to 17 spans, plus one end post gives 18 line posts. One gate adds two gate posts, so 20 posts before waste. A 5% allowance raises the order to 21 posts, and two bags per post gives 42 bags of concrete.
Example 2: 24 m run, 2.4 m spacing, no gates
24 ÷ 2.4 = 10 spans, plus one end post gives 11 posts. With no waste allowance the order stays at 11 posts and 22 bags. This is a clean multiple of the spacing, so no partial panel is created.
Example 3: 60 m run, 3 m spacing, two gates, 10% waste
60 ÷ 3 = 20 spans, plus one end post gives 21 line posts. Two gates add four gate posts, so 25 before waste. A 10% allowance raises the order to 28 posts, and 56 bags at two bags per post.
What the result means
The post count is a purchase quantity, not a layout drawing. It assumes a straight run on ground where spacing can be kept uniform. Corners, changes in elevation, and short closing panels usually add posts, because a panel that does not fit the module needs a post to land on. Gate posts carry the gate leaf and its swing, so they are often larger and set deeper than line posts; the concrete estimate here uses the same two bags for every post, which is a starting point rather than a specification. If your local code, fence height, wind exposure, or soil type requires deeper holes or larger posts, the concrete volume rises quickly because it scales with the square of the hole diameter.
Common mistakes
- Counting one post per panel and forgetting the post at the end of the run.
- Using the panel width as the post spacing when the two are different.
- Forgetting that each gate needs two gate posts, not one.
- Buying concrete for a 200 mm hole and then digging a 300 mm hole.
- Setting posts without checking local height limits, setbacks, or the property line.
Assumptions and limits
- The fence run is straight and the spacing can be held uniform.
- The fence length includes gate openings, which are part of the run.
- Each gate adds two gate posts and no extra line posts.
- Concrete is two 20 kg bags per post, enough for a 200 mm × 600 mm hole in normal soil.
- Waste is applied to the post count and therefore to the bag count.
Frequently asked questions
How many posts do I need for a fence?
Divide the fence length by the post spacing, round up, add one for the final end post, and add two posts for every gate. Then add your waste allowance. A 40 m run at 2.4 m spacing needs 18 line posts before gates.
Should I use post spacing or panel width?
They are different numbers. Post spacing is the centre-to-centre distance you set; panel width is the width of the panel that fills the gap. Panels are often slightly narrower than the spacing so they can be fixed to the posts. Enter the spacing in this calculator.
Why do gates add two posts?
A gate opening is framed by a post on each side. Those posts carry the gate leaf, the hinges, and the latch, so they are usually larger and set deeper than line posts. A double gate needs the same two hinge-side posts plus a meeting post or drop rod.
How much concrete does a fence post need?
It depends on the hole, not the post. A 200 mm diameter hole 600 mm deep takes about 0.019 m³ of concrete, which is roughly two 20 kg bags of setting mix. A wider or deeper hole needs proportionally more; a 300 mm hole takes more than twice as much as a 200 mm hole at the same depth.
Does the calculator add waste to the concrete?
Yes, indirectly. The waste allowance increases the post count, and the bag count follows the increased post count, so the order covers spare posts and their concrete. It does not add a separate allowance for spillage or over-digging.
Can I use this for a chain-link or metal fence?
The post arithmetic still applies, but the concrete and post sizes do not. Chain-link and steel posts use different footing details and hardware, so treat the post count as a starting point and use the manufacturer's setting instructions.
Sources
2026 update
How to use the professional output
This page is not just a formula box. The result is designed to be checked, compared, and taken away.
- Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
- A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
- Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.
The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.