What this calculator does
Drainage pipe needs a fall so water can move by gravity. The fall is the vertical drop over the run, and the invert is the inside bottom of the pipe. A 2% slope drops 2 metres for every 100 metres of pipe, which is the same as 20 mm per metre or a gradient of 1 in 50. This calculator converts between those forms and gives the end invert level so you can set levels on site. It does not choose the slope for you: the right slope depends on pipe size, material, flow rate, and the minimum self-cleansing velocity required by the applicable code.
How to use it
- Enter the pipe run length in metres.
- Enter the slope as a percentage, where 1% is a 1 m fall per 100 m.
- Enter the start invert level as an elevation in metres.
- Read the fall, end invert, gradient, and fall per metre.
- Check the result against the minimum slope and velocity required for the pipe.
How it works
Example calculations
Example 1: 20 m at 2%
The fall is 0.40 m, or 20.0 mm per metre. The gradient is 1 in 50. Starting at an invert of 10.00 m, the downstream invert is 9.60 m.
Example 2: 35 m at 1.5%
The fall is 0.525 m and the gradient is 1 in 66.7. From a start invert of 12.00 m, the end invert is 11.475 m. The fall is 3.50 pipe diameters.
Example 3: 12 m at 1%
A 12 m run at 1% falls 0.120 m, or 10.0 mm per metre. The end invert is 4.880 m. A flatter slope saves depth but may not maintain self-cleansing velocity.
What the result means
The invert is an elevation, so a lower number downstream means the pipe is falling in the direction of flow. Keep the reference datum consistent across the whole run. A slope that is too flat allows solids to settle; a slope that is too steep can cause scour and noisy flow. The commonly cited minimum for small drainage pipes is around 1% to 2%, but the actual requirement depends on the code and the pipe. This calculator does not check velocity, capacity, or hydraulic grade line, and it assumes a straight run with no fittings.
Common mistakes
- Confusing slope percentage with degrees.
- Adding the fall instead of subtracting it from the start invert.
- Measuring the run along the pipe rather than the horizontal distance.
- Ignoring the minimum velocity needed to keep the pipe clear.
- Mixing elevation datums between the start and end of the run.
Assumptions and limits
- The run is straight and the slope is constant.
- The slope percentage is the vertical fall per 100 units of horizontal run.
- The start invert is in the same elevation datum as the result.
- No fittings, bends, or changes in pipe size are modeled.
- Hydraulic capacity and velocity are outside the calculation.
Frequently asked questions
What is an invert level?
The invert is the lowest inside point of the pipe. The invert level is its elevation relative to a chosen datum. It is used to set the pipe so that water flows downhill.
How do I convert a slope percentage to a ratio?
Divide 100 by the percentage. A 2% slope is 100 / 2 = 50, or 1 in 50. A 1% slope is 1 in 100.
How many mm per metre is a 1% slope?
One percent is 10 mm per metre, because 1% of 1,000 mm is 10 mm. A 2% slope is 20 mm per metre.
What is the minimum slope for drainage pipe?
It depends on the pipe size, material, and code. Small pipes often use 1% to 2%, but the requirement should be taken from the applicable code or engineer's design, not from a rule of thumb.
Does a steeper slope always drain better?
Not always. Steep slopes increase velocity and can cause scour or hydraulic jumps, and they may not be possible given the available depth. The design needs to balance fall, capacity, and self-cleansing velocity.
Can I use this for a roof gutter or a swale?
The geometry applies, but the design criteria do not. Gutters and swales have different capacity and erosion considerations. Use a tool or reference specific to that system.
Sources
2026 update
How to use the professional output
This page is not just a formula box. The result is designed to be checked, compared, and taken away.
- Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
- A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
- Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.
The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.