What this calculator does
The most common download mistake is mixing up bits and bytes. Internet plans are sold in megabits per second, while file sizes are shown in megabytes, and one byte is eight bits. A 100 Mbps connection therefore downloads about 12.5 MB per second in ideal conditions, not 100 MB per second. This calculator converts both sides to bits, divides, and adds an allowance for protocol overhead, then presents the result in the unit that makes sense for the size: seconds for a song, minutes for a video, hours for a large backup. The estimate is an upper bound in practice. Wi-Fi, congestion, server limits, disk speed, and the number of parallel connections all reduce the real rate, and upload speeds are often much lower than download speeds on the same plan. Use the result to plan a transfer, not to benchmark a connection.
How to use it
- Enter the file size and choose megabytes, gigabytes, or terabytes.
- Enter the connection speed and choose megabits or megabytes per second.
- Keep the overhead allowance unless you know the protocol is unusually efficient.
- Read the estimated time and the effective speed in MB/s.
- Compare the estimate with the actual speed shown by your download manager.
- For uploads, use the upload speed from your plan, not the download speed.
How it works
Example calculations
Example 1: A 1.5 GB file at 100 Mbps
The file is 1,536 MB, or 12,885 megabits. At 100 Mbps with 5% overhead, the estimate is 135.3 seconds, or about 2.3 minutes. The effective speed is 11.92 MB/s.
Example 2: A 500 MB file at 50 Mbps
A smaller file on a slower plan takes 88.1 seconds, about 1.5 minutes, at 5.96 MB/s. Doubling the speed would roughly halve the time, but only if the server can deliver at that rate.
Example 3: A 50 GB backup at 1 Gbps
A 51,200 MB file at 1,000 Mbps takes 451.0 seconds, or about 7.5 minutes, at 119.21 MB/s. In practice, the server, the disk, and the network path usually matter more than the plan speed at this size.
What the result means
The conversion factor of eight is the whole story, and the overhead allowance is the reality check. A connection rated at 100 Mbps rarely delivers 12.5 MB/s for a single transfer, because the server, the route, and the protocol add delay. The estimate is therefore optimistic, which is useful for planning: if the answer is already too slow, the real transfer will be worse. Uploads deserve separate attention, because many home plans are asymmetric and the upload speed can be a fraction of the download speed. For very large files, the bottleneck often moves to the disk or the server, and parallel connections may help or may not, depending on how the server limits each client.
Common mistakes
- Treating megabits per second as megabytes per second.
- Using the advertised plan speed as the actual transfer rate.
- Forgetting that upload speed is often much lower than download speed.
- Ignoring overhead, especially on many small files rather than one large one.
- Assuming the server can saturate the connection.
- Mixing decimal and binary units without noticing the difference.
Assumptions and limits
- The connection sustains the stated speed for the whole transfer.
- The server and the network path can deliver at that rate.
- The file is a single stream, not many small requests.
- 1 MB is 1,024 × 1,024 bytes and 1 GB is 1,024 MB.
- Overhead covers protocol headers, setup, and retries as a percentage.
- No other traffic competes for the same connection.
Frequently asked questions
How long does a 1 GB download take?
It depends on the speed. At 100 Mbps with 5% overhead, a 1 GB file takes about 1.4 minutes. At 50 Mbps it takes about twice as long, and at 1 Gbps about a tenth.
Why is my download slower than the plan speed?
Wi-Fi, congestion, the server's upload limit, disk speed, and protocol overhead all reduce the rate. A single transfer rarely saturates a fast connection, and peak-hour congestion can cut it further.
What is the difference between Mbps and MB/s?
Mbps means megabits per second; MB/s means megabytes per second. There are eight bits in a byte, so 100 Mbps is about 12.5 MB/s before overhead.
Does the calculator work for uploads?
Yes, if you enter the upload speed from your plan. Many home connections upload much more slowly than they download, so using the download figure would understate the time.
Why does the estimate include overhead?
Real transfers carry protocol headers, connection setup, and retries. A small allowance makes the estimate more realistic, especially for many small files or a noisy connection.
Is 1 GB equal to 1,000 MB?
This calculator uses 1 GB = 1,024 MB, the binary convention common in operating systems. Storage manufacturers sometimes use 1,000 MB, which makes a drive look larger than the operating system reports.
Sources
2026 update
How to use the professional output
This page is not just a formula box. The result is designed to be checked, compared, and taken away.
- Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
- A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
- Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.
The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.