Skip to content

Epoxy Resin Calculator

Enter the coverage area, coating thickness, number of coats, mixed density, A-to-B mix ratio, and a waste allowance. The calculator converts the area and thickness into litres, then into kilograms, and splits the total into part A and part B. Ten square metres at 3 mm with a 1.1 kg/L resin and a 2:1 mix needs 30 litres, 36.3 kg with waste, or 24.2 kg of part A and 12.1 kg of part B.

Updated 2026-11-19 Editorial estimate Calccc Editorial Team Free · No sign-up
m2
mm
coats
kg/L

Check the product data sheet; most casting resins are around 1.05 to 1.2 kg/L.

For a 2:1 mix by weight, enter 2. For a 1:1 mix, enter 1.

%
Scenarios A/BSave two input sets and compare the results. Stored only in this browser.
AEmpty
BEmpty

Your inputs stay in this browser. No account, no uploads.

Professional worksheet

Detailed schedule & assumptions

Inputs used, method, sensitivity, and any year-by-year table. The summary above stays compact; the audit lives here.

Professional worksheet

Inputs, scope, and sensitivity

Inputs used

Method and scope

Result audit

MetricValue

What this calculator does

Epoxy is sold as two components that must be mixed in a fixed ratio, and the cost of getting the quantity wrong is high: mixed resin has a working life measured in minutes to hours, and unused mixed resin cannot be stored. Under-buying means a second order and a visible cold joint between pours. Over-buying wastes material that may not be returnable. The quantity itself is straightforward geometry: a litre of resin covers one square metre at one millimetre, so area times thickness gives litres, and density converts litres to kilograms. The tricky parts are the waste allowance, the number of coats, and the ratio. A 2:1 ratio by weight is not the same as 2:1 by volume, and mixing by the wrong convention throws off the cure. This calculator works in metric units and separates the total into the two parts so the mixing bucket can be filled with confidence.

How to use it

  1. Measure the area to be covered in square metres.
  2. Enter the wet film thickness in millimetres for one coat.
  3. Enter the number of coats if the product is applied in layers.
  4. Check the mixed density on the product data sheet.
  5. Enter the A-to-B ratio exactly as the manufacturer states it.
  6. Add a waste allowance for mixing loss, roller pickup, and edges, then split the total into part A and part B.

How it works

Litres = area (m2) × thickness (mm) × coats. Kilograms = litres × density (kg/L) × (1 + waste percentage / 100). Part A = kilograms × ratio / (ratio + 1). Part B = kilograms / (ratio + 1). In the default case 10 m2 × 3 mm = 30 L, and 30 L × 1.1 kg/L × 1.10 = 36.3 kg, split into 24.2 kg of part A and 12.1 kg of part B.

Example calculations

Example 1: A countertop coating

A 4 m2 countertop is coated at 2 mm with a 1.1 kg/L resin in a 2:1 mix and a 10% waste allowance. The volume is 4 × 2 = 8 L, the weight is 8 × 1.1 × 1.10 = 9.68 kg, and the split is 6.45 kg of part A and 3.23 kg of part B. A countertop pour is usually done in one pass, so mixing slightly more than the estimate is safer than running short halfway across the surface.

Example 2: A garage floor

A 30 m2 garage floor gets a 0.5 mm coat with the same resin and a 10% waste allowance. The volume is 15 L, the weight is 18.15 kg, and the split is 12.1 kg of part A and 6.05 kg of part B. Thin coatings are less forgiving of surface texture: a rough floor needs more material than the nominal thickness suggests, so the waste allowance should reflect the substrate.

Example 3: A thick casting

A 0.5 m2 mould is filled to 20 mm with a 1.05 kg/L casting resin in a 1:1 mix and a 15% waste allowance. The volume is 10 L, the weight is 12.08 kg, and the split is 6.04 kg of part A and 6.04 kg of part B. Thick casts generate heat, so the pour may need to be done in layers even though the total quantity is calculated in one go.

What the result means

The total weight is what to buy, and the part A and part B figures are what to weigh into the mixing bucket. Treat the calculated quantity as a lower bound: surfaces absorb resin, rollers and mixing sticks retain some, and edges and vertical faces need more than a flat area suggests. The waste allowance is the lever for that uncertainty. A 10% allowance is reasonable for a smooth, sealed surface; a porous or rough surface may need 15% to 20%. The ratio is the other critical input. Most laminating and casting resins specify a ratio by weight, while some coating kits specify by volume, and the two give different splits. Check the data sheet, use a scale for weight ratios, and mix for the full time recommended before adding fillers or pouring.

Common mistakes

  • Mixing by volume when the data sheet gives a ratio by weight, or the reverse.
  • Ignoring the waste allowance and running short partway through a pour.
  • Rounding the total down to the nearest pack size instead of up.
  • Mixing a large batch that exceeds the working life and sets in the bucket.
  • Adding part B by eye instead of weighing it accurately.
  • Pouring thick sections in one pass without checking the product's maximum layer thickness.

Assumptions and limits

  • The area is flat and the thickness is uniform across it.
  • The surface does not absorb a significant amount of resin beyond the waste allowance.
  • The mixed density is the one given on the product data sheet.
  • The ratio is by weight, as entered.
  • No fillers, pigments, or embedded objects change the volume.
  • The waste allowance covers mixing loss, tools, and edges.

Frequently asked questions

How much epoxy do I need per square metre?

At 1 mm thick, one square metre needs one litre of mixed resin. At 3 mm it needs three litres. Multiply by the density to get kilograms, and add a waste allowance for the surface and the tools.

What does a 2:1 mix ratio mean?

It means two parts of part A to one part of part B. If the ratio is by weight, weigh 2 kg of A for every 1 kg of B. The total is split into three equal shares, with two going to A and one to B.

How much waste allowance should I add?

About 10% for a smooth, sealed surface, and 15% to 20% for a rough or porous one. Edges, vertical faces, and small batches tend to need a higher allowance.

Can I pour epoxy thicker than the data sheet allows?

Not in one pass. Thick pours generate heat and can crack or yellow. The data sheet gives a maximum layer thickness, and deep casts are usually built up in layers within the recoat window.

Does temperature affect the quantity?

It affects the working life and the viscosity more than the quantity. Warm resin sets faster and flows more easily; cold resin is thicker and traps air. The volume and weight for a given area and thickness stay the same.

How do I split the total into part A and part B?

For a ratio of A to B, divide the total weight by (ratio + 1) to get one part. Multiply that by the ratio for part A and keep one part for part B. The calculator does this split for the ratio you enter.

Sources

This calculator is an educational planning tool, not financial, legal, insurance, medical, or professional advice. Results depend on the inputs and on rules that vary by place and provider. Confirm important decisions with a qualified professional and the relevant documents.

2026 update

How to use the professional output

This page is not just a formula box. The result is designed to be checked, compared, and taken away.

  • Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
  • A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
  • Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.

The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.

Calccc Editorial Team · Updated 2026-11-19

Prepared by Calccc Editorial Team as an educational estimate. This page is not a licensed professional review and is not financial, medical, legal, or tax advice.

Editorial estimate prepared by the Calccc Editorial Team; not a licensed professional review.