Skip to content

Countertop Calculator

Enter the total counter length, depth, and backsplash height, plus the slab size and waste allowance. The calculator returns counter area, backsplash area, total area with waste, the number of slabs to order, and the length of edge to finish.

Updated 2026-11-18 Editorial estimate Calccc Editorial Team Free · No sign-up
m

Add up every run, including islands and peninsulas.

mm
mm

Set 0 if you are not tiling or cladding a backsplash.

mm
mm
%

Cut-outs, veining direction, and sink placement all consume slab area.

Scenarios A/BSave two input sets and compare the results. Stored only in this browser.
AEmpty
BEmpty

Your inputs stay in this browser. No account, no uploads.

Professional worksheet

Detailed schedule & assumptions

Inputs used, method, sensitivity, and any year-by-year table. The summary above stays compact; the audit lives here.

Professional worksheet

Inputs, scope, and sensitivity

Inputs used

Method and scope

Result audit

MetricValue

What this calculator does

Stone countertops are sold by the slab, not by the square metre, so the ordering question is how many slabs to buy rather than how much area the kitchen has. Those are different numbers. A run of counters plus a backsplash might total four square metres, which fits inside a single slab on paper, yet the fabricator may still need two because of the way the pieces nest, the direction of the veining, and the space lost around a sink cut-out. This calculator gives both figures: the measured area and the slab count that results from dividing it, with waste, by the slab size. It also reports the edge length, which is quoted separately for most profiles and is easy to underestimate when there are islands and peninsulas.

How to use it

  1. Add up every counter run, including islands and peninsulas.
  2. Measure the depth of the counters, usually 600 mm.
  3. Add a backsplash height if the splash is built from the same stone.
  4. Enter the slab dimensions from the fabricator or stone yard.
  5. Increase the waste allowance for veined stone or complex cut-outs.

How it works

Counter area = length x depth. Backsplash area = length x height. Slabs = ceil(total area x (1 + waste) / slab area). Edge length = length + 2 x depth. In the default case, 3.60 m² of counter plus 0.60 m² of splash is 4.62 m² with waste, which fits in 1 slab of 5.12 m².

Example calculations

Example 1: 6 m of counter with a 100 mm splash

Counter area is 3.60 m² and the splash adds 0.60 m². Adding 10% waste gives 4.62 m², comfortably inside a 5.12 m² slab, so one slab is enough.

Example 2: A larger kitchen with a taller splash

Nine metres at 650 mm deep is 5.85 m², and a 150 mm splash adds 1.35 m². With 15% waste the order needs 2 slabs, and the edge run is 10.30 m.

Example 3: Counters only, no stone splash

Twelve metres with no backsplash gives 7.20 m² before waste and 7.92 m² after, which rounds up to 2 slabs. The surplus of 2.32 m² is normal and is what pays for seams and cut-outs.

What the result means

Slab count is a purchasing decision, not a cutting plan. A fabricator will lay out the actual pieces on the slab, and the nesting rarely matches a simple area division: an L-shaped run, a sink cut-out, or a book-matched vein can force an extra slab even when the arithmetic says otherwise. Edge profile and edge length are usually priced per linear metre, and the front edge of every run counts, not just the perimeter of the room. Backsplash height is often reduced behind upper cabinets and raised behind the hob, so a single height is an approximation. Ask for a layout drawing before approving the order.

Common mistakes

  • Ordering by area and assuming a single slab will nest the pieces.
  • Leaving out islands and peninsulas from the run length.
  • Ignoring the vein direction on a patterned stone.
  • Forgetting that the edge length includes the ends of every run.
  • Assuming the fabricator's slab size matches the stone yard's.
  • Underestimating waste for a sink, hob, or tap cut-out.

Assumptions and limits

  • All counters have the same depth and backsplash height.
  • Slab dimensions are the usable size after trimming.
  • Waste allowance covers cut-outs, offcuts, and pattern matching.
  • Edge length is the front edge plus the two exposed returns.
  • Installation, cut-outs, and edge polishing are quoted separately.

Frequently asked questions

How many slabs do I need for a kitchen?

Divide the total area, including waste, by the slab area and round up. A typical kitchen of four to six square metres often fits one or two slabs, but the layout and veining decide the real answer.

Why does the calculator round up so aggressively?

Because slabs cannot be joined invisibly. Once the area exceeds a slab, a second slab is required even if only a small piece is needed, and the leftover cannot be used elsewhere on the same job.

What is a typical slab size?

Jumbo slabs are often around 3.2 m by 1.6 m, though sizes vary by material and supplier. Always use the dimensions the fabricator confirms.

How much waste should I allow?

Ten percent is a reasonable default for plain stone. Use 15 to 20 percent for veined or book-matched material, or where the layout has many cut-outs.

Does the backsplash need the same stone?

Not necessarily. Many kitchens use tile for the splash, which is cheaper and easier to replace. Set the height to zero if the splash is not stone.

How is edge length measured?

Along the front of every counter, plus any exposed ends or returns. Islands have a front edge and often two ends, so their edge length is greater than their length.

Sources

This calculator estimates area and slab count. It is not a cutting plan or a fabrication quote; seams, veining, cut-outs, and installation are decided by the fabricator. Confirm dimensions and slab availability before ordering.

2026 update

How to use the professional output

This page is not just a formula box. The result is designed to be checked, compared, and taken away.

  • Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
  • A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
  • Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.

The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.

Calccc Editorial Team · Updated 2026-11-18

Prepared by Calccc Editorial Team as an educational estimate. This page is not a licensed professional review and is not financial, medical, legal, or tax advice.

Editorial estimate prepared by the Calccc Editorial Team; not a licensed professional review.