The short answer: kWh = watts × hours ÷ 1,000. Cost = kWh × price per kWh. A 1,500 W heater running 2 hours uses 3 kWh; at $0.15/kWh, $0.45. Use the actual wattage and run time, not the label’s maximum if the device cycles.

Key takeaways

  • Watts are power; kWh is energy.
  • 1,000 W for 1 hour = 1 kWh.
  • Your rate is on the bill.
  • Cycling appliances use less than their peak.
  • Standby loads add up.

The formula

kWh = W × hours ÷ 1,000. Cost = kWh × rate. A 60 W fan for 8 hours: 60 × 8 ÷ 1,000 = 0.48 kWh; at $0.16/kWh, $0.077. A 1,500 W space heater for 4 hours: 6 kWh; $0.96. A 2,000 W dryer for 1 hour: 2 kWh; $0.32.

Peak vs actual

A refrigerator cycles; its compressor does not run all day at the label wattage. A heater may cycle on a thermostat. An oven heats and holds. Use a plug-in energy monitor for a week to get the actual kWh, or use the label wattage and an estimated duty cycle.

An example

A 1,200 W space heater used 5 hours a day for 30 days: 1,200 × 5 × 30 ÷ 1,000 = 180 kWh. At $0.15/kWh, $27. A 60 W fan 8 hours a day for 30 days: 14.4 kWh, $2.16. The heater dominates.

Rate structure

Electricity rates may be flat, tiered, or time-of-use. A time-of-use plan charges more during peak hours. The average rate on the bill may differ from the marginal rate. Use the marginal rate for the cost of an extra hour. Add taxes and fees if the bill separates them.

Standby and phantom loads

TVs, chargers, and game consoles draw power when idle. A few watts per device can add up over a year. A smart strip can cut standby power. The biggest savings usually come from heating, cooling, water heating, and large appliances.

What to compare

Compare the wattage, hours, duty cycle, and rate. A device with a high peak but short run time may use less than a low-power device that runs all day.

A whole-home example

A 1,500 W space heater 4 hours/day, a 60 W fan 8 hours/day, and a 100 W TV 5 hours/day for 30 days: heater 180 kWh, fan 14.4 kWh, TV 15 kWh. Total 209.4 kWh. At $0.16/kWh, $33.50. The heater is 86% of the cost.

Energy monitor

A plug-in monitor measures actual kWh over time, including cycling. Use it for a week on a refrigerator, heater, or game console. The label wattage is a maximum, not average consumption.

Tiered rates

If the bill has tiers, the marginal rate for the next kWh may be higher than the average. Use the marginal rate to estimate the cost of adding a load. Time-of-use plans can make the same appliance cheaper or more expensive depending on the hour.

What to compare

Compare the wattage, hours, duty cycle, and rate. A high-wattage device used briefly may cost less than a low-wattage device left on.

Water heater and HVAC

Water heating, heating, and cooling are often the largest loads. A 4,500 W water heater running 3 hours a day uses 13.5 kWh; at $0.16, $2.16 a day. A 3,500 W AC running 8 hours uses 28 kWh; $4.48 a day. Actual run time depends on the thermostat and insulation.

What to compare

Compare the wattage, run time, and rate. A whole-home estimate should use actual duty cycles, not label maximums.

Cost per cycle

A dishwasher cycle may use 1–2 kWh; a load of laundry 0.5–2 kWh depending on the water temperature. A heat-pump dryer uses less than a resistance dryer. Use the appliance’s energy label or a monitor. The cost per cycle is easier to compare than the annual label.

What to compare

Compare the kWh per cycle, the rate, and the frequency. A slightly higher kWh per cycle used daily can cost more than a lower one used weekly.

Heating vs cooling

A heat pump can be more efficient than a resistance heater, but its performance drops in extreme cold. A 1,500 W space heater is 100% efficient at the point of use, but the electricity may be generated at a lower efficiency. Compare the cost per kWh and the heat delivered.

What to compare

Compare the device’s kWh, the rate, and the heat output. A higher-wattage device is not always more expensive to run if it heats faster.

Cost per year

A 100 W device left on 24/7 uses 876 kWh a year. At $0.16/kWh, $140. A 1,500 W heater used 2 hours a day uses 1,095 kWh, $175. A device that runs constantly can cost more than a high-wattage device used briefly.

What to compare

Compare the annual kWh and cost, not the wattage alone.

What to compare

Compare the annual kWh and cost, and use the marginal rate for an extra load.

Final check

Compare the annual kWh and cost, and use the marginal rate for an extra load. A plug-in monitor gives the actual duty cycle.

Check the actual duty cycle with a plug-in monitor before using the label wattage.

Use the marginal rate for an extra load.

Check the actual duty cycle with a monitor and use the marginal rate for an extra load.

Now check.

Now check.

Frequently asked questions

How do I calculate kWh?

Watts × hours ÷ 1,000.

How much does a 1,500 W heater cost per hour?

At $0.15/kWh, 1.5 kWh × $0.15 = $0.225 per hour.

Why is my bill higher than the calculator?

Taxes, fees, tiered rates, and other appliances add to the total. The calculator estimates one device.

Do standby devices matter?

They can add a few percent to the bill. The biggest loads are heating, cooling, and water heating.

Further reading

Keep exploring

Read next Roofing: Squares, Pitch, Waste, and Cost Convert a roof footprint into sloped area, squares, and bundles with the pitch multiplier. Includes waste allowances, a… Read next Wallpaper: Rolls, Pattern Repeat, and Waste Estimate wallpaper rolls from wall area, roll coverage, pattern repeat, and openings. Learn the area formula, a strip-count… Read next MPG: Real-World Fuel Economy and Cost per Mile MPG is miles divided by gallons, and cost per mile is price divided by MPG. Learn to measure…