The short answer: fence length is the linear distance around the run. Posts are spaced 6–8 feet apart, with an extra post at each end and at gates. Pickets = fence length ÷ picket width plus gap, rounded up. Concrete is about 1–2 bags per post, depending on hole size.

Key takeaways

  • Measure the actual run, including corners and gates.
  • Post spacing affects the post count.
  • Rails are horizontal; pickets are vertical.
  • Gates need stronger posts and hardware.
  • Concrete volume depends on hole size.

Post count

For a straight run of 100 ft with posts every 8 ft, you need 100 ÷ 8 = 12.5, so 14 posts including both ends. For 6 ft spacing, 100 ÷ 6 = 16.7, so 18 posts. Add posts at gates and corners. A corner post carries two directions of load and should be braced.

Rails and pickets

A typical privacy fence has two or three horizontal rails. Rails = number of sections × rails per section. Pickets: fence length in inches ÷ (picket width + gap). For a 100 ft fence with 5.5 in pickets and a 0.25 in gap: 1,200 ÷ 5.75 = 208.7, so 209 pickets. Add 5–10% for cuts and defects.

Concrete

A 10 in diameter hole 30 in deep has a volume of about 1.36 cu ft, or 0.05 cu yd. An 80 lb bag of concrete mix yields about 0.6 cu ft. Two bags fill the hole with some margin. Larger holes, frost depth, and gate posts need more. Check the bag yield and the local frost depth.

Gates

A gate needs a frame, hinges, a latch, and a stronger post. A 4 ft gate is common for a walkway; a 10–12 ft gate needs a different frame and possibly a wheel. Do not hang a heavy gate on a single thin post.

What to compare

Compare the linear feet, post spacing, picket count, concrete, and hardware. A cheap fence with too few posts may sag. A fence with too many posts costs more but is stronger.

A 100 ft example

100 ft run, posts every 8 ft: 12.5 spaces, so 14 posts including ends. Two rails per section: 13 sections × 2 = 26 rails. Pickets 5.5 in with 0.25 in gap: 1,200 ÷ 5.75 = 208.7, so 209, plus 5% = 220. Concrete: 14 posts × 2 bags = 28 bags.

Post depth

Set posts below the frost line, often 30–48 in, with 6 in of gravel at the bottom. A 10 in hole with 2 bags of mix is a common starting point. Gate posts need larger holes and stronger posts.

Layout

Run a string line and mark post centers. Check the corners with the 3-4-5 method. A fence that is not square will show at the gates.

What to compare

Compare the post count, rail count, picket count, concrete, and hardware. A cheap fence with too few posts may sag.

Gates and corners

A gate needs a frame and a stronger post. A 4 ft walk gate is common; a 10–12 ft drive gate needs a different frame and maybe a wheel. A corner post carries two directions of fence and should be braced. Add the gate hardware to the budget.

Code and setbacks

Many jurisdictions limit fence height, require a permit, and set setbacks from property lines. A fence on a property line may need a survey. Check before building; moving a fence is expensive.

What to compare

Compare the post count, picket count, concrete, gate hardware, and permit requirements.

Material choices

Wood, vinyl, composite, and chain link have different post spacing, panel sizes, and hardware. A wood privacy fence needs rails and pickets; a vinyl panel system may use prebuilt panels. The calculator’s picket formula applies to a stick-built wood fence; panel systems are counted by panel.

What to compare

Compare the material, panel or picket count, post spacing, and hardware. A cheap material with a short life can cost more over time.

A 150 ft example

150 ft run, posts every 8 ft: 18.75 spaces, so 20 posts. Two rails: 19 sections × 2 = 38 rails. Pickets 5.5 in with 0.25 in gap: 1,800 ÷ 5.75 = 313, plus 5% = 329. Concrete: 20 × 2 = 40 bags. Add gate posts and hardware.

What to compare

Compare the post count, rail count, picket count, concrete, and gate hardware.

What to compare

Compare the post count, rail count, picket count, concrete, gate hardware, and permit requirements. A fence with too few posts may sag; a fence with too many costs more but is stronger.

Check the property line and local height rules before building.

Fence height and wind

A taller fence catches more wind and needs stronger posts and deeper footings. A 6 ft privacy fence is common; an 8 ft fence may need engineering. Check the local height limit and the wind exposure. A fence on a slope needs stepped panels or a racked design.

What to compare

Compare the height, post spacing, panel or picket count, concrete, and hardware before building.

Property lines

Confirm the property line before setting posts. A fence built over the line may have to be moved. A survey is cheaper than rebuilding a fence. Check the local height and setback rules.

What to compare

Compare the post count, picket count, concrete, and permit requirements.

Check the property line and height rules before building.

Frequently asked questions

How far apart should fence posts be?

Usually 6–8 feet, depending on the fence height, wind load, and material. Check local code.

How many pickets do I need?

Divide the fence length in inches by the picket width plus gap, then round up and add 5–10%.

How much concrete per post?

Often 1–2 bags of 80 lb mix, depending on hole size and depth.

Do I need a permit?

Many jurisdictions require a fence permit or have height and setback rules. Check before building.

Further reading

Keep exploring

Read next Roofing: Squares, Pitch, Waste, and Cost Convert a roof footprint into sloped area, squares, and bundles with the pitch multiplier. Includes waste allowances, a… Read next MPG: Real-World Fuel Economy and Cost per Mile MPG is miles divided by gallons, and cost per mile is price divided by MPG. Learn to measure… Read next Party Planning: Guests, Food, Drink, and Budget Estimate food, drink, and cost per guest with a simple multiplication model, then adjust for buffet portions, ice,…