Skip to content

Attic Ventilation Calculator

Enter the attic floor length and width, choose a vent ratio, and set the intake share. The calculator returns the required net free area in square metres and square centimetres, split between intake and exhaust. Net free area is the open area after screens and louvers, not the nominal vent size.

Updated 2026-11-18 Editorial estimate Calccc Editorial Team Free · No sign-up
m
m
Advanced options
%

A balanced design is usually 50–60% intake at the soffits and the rest at ridge or gable vents.

Scenarios A/BSave two input sets and compare the results. Stored only in this browser.
AEmpty
BEmpty

Your inputs stay in this browser. No account, no uploads.

Professional worksheet

Detailed schedule & assumptions

Inputs used, method, sensitivity, and any year-by-year table. The summary above stays compact; the audit lives here.

Professional worksheet

Inputs, scope, and sensitivity

Inputs used

Advanced inputs used

Method and scope

Result audit

MetricValue

What this calculator does

Attic ventilation is sized by net free area (NFA), the open area that actually lets air through. A common rule is one unit of NFA for every 300 units of attic floor area, with a tighter 1/150 ratio in cold climates or where a vapor barrier is limited, and a looser 1/600 ratio in some code allowances. The vent area should be balanced between low intake at the soffits and high exhaust at the ridge or gables. This calculator converts the floor area and ratio into NFA, then splits it. It does not choose a vent product; vent manufacturers publish NFA per piece, and the nominal opening is usually larger than the net area.

How to use it

  1. Measure the attic floor length and width, not the roof slope area.
  2. Choose the vent ratio that matches your climate and code.
  3. Set the intake share; 50–60% low intake is a common balanced design.
  4. Read the total NFA and the intake and exhaust areas.
  5. Convert to vent pieces using each product's published NFA rating.

How it works

Attic floor area = length × width. Required NFA = floor area ÷ vent ratio. Intake NFA = total NFA × intake share. Exhaust NFA = total NFA − intake NFA. In the default case, an 80 m² attic at 1/300 needs 0.267 m² of NFA, or 2,667 cm², split into 1,333 cm² intake and 1,333 cm² exhaust.

Example calculations

Example 1: 10 × 8 m attic at 1/300

The floor area is 80.0 m². At 1/300 the required NFA is 0.267 m², or 2,667 cm². A 50/50 split gives 1,333 cm² of intake and the same amount of exhaust.

Example 2: 12 × 10 m attic at 1/150

The tighter ratio doubles the requirement: 120.0 m² ÷ 150 = 0.80 m², or 8,000 cm². At a 50% intake share, each side needs 4,000 cm² of net free area.

Example 3: 15 × 9 m attic at 1/600, 60% intake

The 1/600 allowance reduces the total to 0.225 m², or 2,250 cm². A 60% intake share puts 1,350 cm² low and 900 cm² high. The looser ratio is only valid where the code and the vapor barrier allow it.

What the result means

The ratio is a minimum, not a target for arbitrary vent placement. A large exhaust vent with no low intake can pull air from the house instead of the soffits, which wastes energy and can worsen moisture. Soffit vents must be open, not blocked by insulation, and ridge vents need a clear slot. The NFA printed on a vent is the number to use; a 300 mm × 300 mm louver with 50% free area provides 0.045 m² of NFA, not 0.09 m². Local codes, shingle warranties, and climate affect the right ratio. In cold climates, air sealing and insulation usually matter more than adding vents.

Common mistakes

  • Using the roof area instead of the attic floor area.
  • Using the vent's nominal size instead of its net free area.
  • Installing all exhaust and no low intake.
  • Blocking soffit vents with insulation or storing boxes against them.
  • Applying a 1/600 allowance where the code or vapor barrier requires 1/150.

Assumptions and limits

  • The attic floor is rectangular and fully ventilated.
  • The vent ratio is the code or manufacturer minimum for the climate.
  • Net free area is measured after screens, louvers, and framing.
  • Intake and exhaust are both unobstructed.
  • No mechanical ventilation or air-conditioned attic is included.

Frequently asked questions

What is net free area?

Net free area is the actual open area of a vent after subtracting the screen, louvers, and frame. It is always smaller than the nominal opening. Use the manufacturer's NFA rating, not the outside dimensions.

Which ratio should I use?

1/300 is a common minimum. 1/150 is used in colder climates or where a vapor barrier is limited; 1/600 appears in some code allowances with a proper vapor barrier. Follow the local code and the shingle manufacturer's requirements.

How do I split intake and exhaust?

A balanced design uses roughly equal NFA low and high, and many builders use 50–60% intake. The exact split depends on the roof design and the vent products. The key is a continuous low intake path and a high exhaust path.

Can I have too much ventilation?

More is not automatically better if it is unbalanced or if it bypasses insulation. Excessive exhaust without intake can depressurize the attic. Design the intake and exhaust together and air-seal the ceiling first.

Do ridge vents count as exhaust?

Yes, ridge vents are a common high exhaust. They need a clear opening at the ridge and should be paired with soffit intake. Some ridge vents perform poorly if the roof deck is not cut back properly.

Does this apply to a conditioned attic?

No. A conditioned or encapsulated attic is inside the building envelope and is insulated at the roof line. It needs a different design, often with no attic ventilation. Consult a building scientist or contractor.

Sources

This calculator is an educational ventilation estimate, not a building-code determination. Required ratios and vent placement vary by climate, code, and roof assembly. Confirm the design with the local building department and the shingle or vent manufacturer.

2026 update

How to use the professional output

This page is not just a formula box. The result is designed to be checked, compared, and taken away.

  • Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
  • A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
  • Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.

The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.

Calccc Editorial Team · Updated 2026-11-18

Prepared by Calccc Editorial Team as an educational estimate. This page is not a licensed professional review and is not financial, medical, legal, or tax advice.

Editorial estimate prepared by the Calccc Editorial Team; not a licensed professional review.