Skip to content

Crown Molding Calculator

Enter the corner angle and the spring angle of the molding. The calculator returns the miter and bevel angles to set on the saw, then adds waste to your run and divides it by the stock length to show how many pieces to buy and how much will be left over.

Updated 2026-11-18 Editorial estimate Calccc Editorial Team Free · No sign-up
°

90° for a square room. Measure out-of-square corners before cutting.

m

Perimeter of the room where crown is installed.

%

10% is a sensible starting point for cut ends and defects.

Scenarios A/BSave two input sets and compare the results. Stored only in this browser.
AEmpty
BEmpty

Your inputs stay in this browser. No account, no uploads.

Professional worksheet

Detailed schedule & assumptions

Inputs used, method, sensitivity, and any year-by-year table. The summary above stays compact; the audit lives here.

Professional worksheet

Inputs, scope, and sensitivity

Inputs used

Method and scope

Result audit

MetricValue

What this calculator does

Crown molding is cut on the saw with the molding nested upside down against the fence, and the angles are not 45 degrees. Because the molding sits at an angle to both the wall and the ceiling, the saw has to combine two rotations, which is why a square corner with common 38-degree crown needs roughly 31.6 degrees of miter and 33.9 degrees of bevel. The numbers come from two trigonometric relationships that depend on the spring angle and the actual corner angle, and they change whenever either changes. Rooms are rarely perfectly square, so measuring the corner is worth more than assuming ninety degrees. This calculator produces the angles and also the buying quantity, since a long run is wasted quickly if the stock length and waste allowance are not planned.

How to use it

  1. Measure the corner angle with a protractor or angle finder.
  2. Select the spring angle that matches the molding profile.
  3. Enter the total run where crown will be installed.
  4. Choose the stock length you can buy locally.
  5. Cut a test piece from scrap before committing to the full run.

How it works

With spring angle S and corner angle C: miter = atan(sin S x tan(C/2)) and bevel = asin(cos S x sin(C/2)). A 90-degree corner with 38-degree crown gives 31.6 degrees of miter and 33.9 degrees of bevel. Pieces = ceil(total run x (1 + waste) / stock length).

Example calculations

Example 1: A square corner with 38-degree crown

The saw settings are 31.6 degrees miter and 33.9 degrees bevel. For 18.0 m of run with 10% waste, you need 9 pieces of 2.4 m, leaving 1.80 m spare.

Example 2: The same corner with 45-degree crown

A 45-degree spring angle gives 35.3 degrees miter and 30.0 degrees bevel. The steeper spring angle pushes the miter up and the bevel down, so the two profiles cannot share a saw setting even in the same room.

Example 3: A 120-degree corner in a bay

An obtuse corner changes both angles: 46.8 degrees miter and 43.0 degrees bevel. With 26.0 m of run and 15% waste you need 10 pieces of 3.0 m.

What the result means

The formula assumes the molding is nested the way it will hang, with the top edge against the saw fence. That orientation matters: cutting crown flat on the saw bed uses different settings and is a common source of gaps. Real corners are usually a degree or two off square, and a wall that leans or a ceiling that sags changes the spring angle along the run. For those cases, cope the internal corners instead of mitering both sides, and sneak up on outside corners with a test cut. Buying an extra piece is cheaper than a second trip, which is why the waste allowance defaults to ten percent.

Common mistakes

  • Setting the saw to 45 degrees for a square corner.
  • Cutting crown flat instead of nested against the fence.
  • Assuming every corner in the room is exactly 90 degrees.
  • Forgetting that inside corners are usually coped, not mitered.
  • Measuring the wall rather than the actual molding run, including outside corners.
  • Buying exactly the calculated length with no allowance for defects or miscuts.

Assumptions and limits

  • The corner angle is measured accurately and is constant top to bottom.
  • The molding is nested upside down against the saw fence.
  • The spring angle matches the profile and the installation.
  • Stock pieces are straight and free of defects.
  • Waste covers cut ends and minor miscuts but not a change of design.

Frequently asked questions

Why isn't the miter 45 degrees?

Because crown molding sits at an angle to the wall and the ceiling. The saw has to combine the corner rotation with the spring angle, which produces a smaller miter and a matching bevel. Only flat trim cut in the plane of the wall uses a true 45.

What is spring angle?

The angle between the back of the molding and the wall, typically 38 or 45 degrees. It is a property of the profile and determines both saw angles.

Should I cope inside corners?

Usually yes. Coped joints tolerate slight out-of-square walls better than miters and stay tight as the building moves. Outside corners are normally mitered.

How do I measure a corner that isn't square?

Use an angle finder or two straight edges and a protractor. Measure the actual angle between the walls, not the angle of the cut, and enter that figure.

Do I need to add waste for a simple room?

Ten percent is a sensible start. Add more for rooms with many corners, long pieces, or fragile profiles, because a snapped end can ruin a whole stick.

Can I use this for baseboard?

No. Baseboard is flat against the wall and uses a simple miter equal to half the corner angle. This calculator is specifically for crown.

Sources

This calculator gives geometric saw settings for crown molding. It does not replace a test cut, and it does not account for wall lean, ceiling sag, or profile-specific quirks. Follow tool safety instructions and local building guidance.

2026 update

How to use the professional output

This page is not just a formula box. The result is designed to be checked, compared, and taken away.

  • Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
  • A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
  • Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.

The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.

Calccc Editorial Team · Updated 2026-11-18

Prepared by Calccc Editorial Team as an educational estimate. This page is not a licensed professional review and is not financial, medical, legal, or tax advice.

Editorial estimate prepared by the Calccc Editorial Team; not a licensed professional review.