What this calculator does
Staining a deck is a coverage problem with a twist: the railing, balusters, and posts take more stain per square foot than the flat decking, and few people include them. This calculator adds a railing allowance based on linear feet, multiplies by the number of coats, and divides by the coverage printed on the stain can. It then rounds up to whole cans and reports the leftover, because a partially used can is hard to store and a short can means a second trip.
How to use it
- Enter the deck surface area, length times width.
- Add the total linear length of railing, posts, and balusters.
- Adjust the railing area factor if your railing is unusually open or closed.
- Enter the number of coats the product recommends.
- Use the coverage per gallon printed on the label.
How it works
Example calculations
Example 1: the default deck
320 sq ft of decking plus 60 sq ft of railing is 380 sq ft. At two coats and 250 sq ft per gallon, 3.04 gallons are needed, so 4 one-gallon cans at $45 cost $180, with 0.96 gallons left and a cost of $0.47 per square foot.
Example 2: a larger deck and railing
500 sq ft of decking plus 100 ft of railing at 1.5 sq ft/ft is 650 sq ft. At two coats and 200 sq ft per gallon, 6.5 gallons are needed, so 7 one-gallon cans at $50 cost $350, leaving half a gallon.
Example 3: a single coat from a five-gallon can
800 sq ft with no railing at one coat and 300 sq ft per gallon needs 2.67 gallons. One five-gallon can at $45 per gallon costs $225 and leaves 2.33 gallons, which is only sensible if you have another deck or fence to coat.
What the result means
Coverage is the input most likely to be wrong, because stain soaks in rather than sitting on the surface. Weathered, dry, or rough-sawn boards absorb much more than smooth, previously sealed boards, and a first coat on bare wood can use almost double the label rate. The railing factor is a planning average: a closed picket rail has more area than an open cable rail. Two thin coats usually outperform one thick coat and last longer, which is why the calculator multiplies by coats instead of letting you compensate with extra stain.
Common mistakes
- Measuring only the decking and forgetting the railing.
- Using the label coverage for a rough or heavily weathered surface.
- Buying exactly the calculated gallons with no margin for the last board.
- Applying one thick coat instead of two thin ones.
- Staining over a damp deck or one that has not been cleaned.
Assumptions and limits
- The deck area is the flat surface, excluding railing and stairs.
- Railing area is estimated as linear feet times the entered factor.
- Coverage per gallon comes from the stain or sealer label.
- The number of coats is applied evenly to deck and railing.
- Can sizes are one gallon or five gallons.
Frequently asked questions
How much does a gallon of deck stain cover?
Typical labels claim 200 to 350 sq ft per gallon per coat. Rough or weathered wood covers less, so check the label and test a small area.
How many coats of stain do I need?
Two coats are common for a new or bare deck and for a colour change. A maintenance coat on a previously stained deck can be a single coat.
How do I estimate railing area?
Multiply the total linear length of railing by an area factor. A picket rail is roughly 1.
Why round up to whole cans?
Stain is sold in fixed sizes, and running short mid-job risks a visible colour break. Buying a whole extra can also gives you touch-up material.
Can I use this for sealer?
Yes. Use the sealer's own coverage rate, which is often higher than a pigmented stain, and note that some sealers need only one coat.
Sources
2026 update
How to use the professional output
This page is not just a formula box. The result is designed to be checked, compared, and taken away.
- Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
- A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
- Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.
The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.