Skip to content

Ramp Calculator

Enter the total rise, the slope you want, and the ramp width. The calculator returns the run needed, the slope as a ratio and an angle, the deck area, and how many rest landings a long ramp will need.

Updated 2026-11-18 Editorial estimate Calccc Editorial Team Free · No sign-up
mm

Height from the lower surface to the top landing.

%

8.33% is the 1:12 ratio used by many accessibility standards for a 600 mm rise.

m
m

Level platform at the top of the ramp.

Scenarios A/BSave two input sets and compare the results. Stored only in this browser.
AEmpty
BEmpty

Your inputs stay in this browser. No account, no uploads.

Professional worksheet

Detailed schedule & assumptions

Inputs used, method, sensitivity, and any year-by-year table. The summary above stays compact; the audit lives here.

Professional worksheet

Inputs, scope, and sensitivity

Inputs used

Method and scope

Result audit

MetricValue

What this calculator does

A ramp is defined by three numbers: the rise it has to climb, the slope it is allowed to use, and the length that results. Slope is usually written as a percentage or a ratio, and the two are the same thing expressed differently: a 1:12 ramp rises one unit for every twelve units of run, which is 8.33 percent. Accessibility standards generally cap the slope and also limit how much rise a single run may cover, which is why long ramps need level rest landings. Getting the run right matters because a ramp that is too steep is hard to use and may not comply, while one that is longer than necessary costs more and consumes yard space. This calculator converts the rise and slope into a buildable length and the area of deck you will need.

How to use it

  1. Measure the total rise from the ground to the top landing.
  2. Choose a slope, starting from the 1:12 ratio many standards require.
  3. Enter the ramp width, allowing for handrails and edge protection.
  4. Add a top landing length so the door or gate has a level approach.
  5. Check the local maximum rise per run and add rest landings where needed.

How it works

Run = rise / slope. Slope ratio = 1 / slope, so 8.33% is 1:12. Total length = run + top landing. Deck area = run x width. In the default case, 0.60 m / 0.0833 = 7.20 m of run, a ratio of 1:12.0, and 8.64 m² of deck.

Example calculations

Example 1: A 600 mm rise at 1:12

The ramp needs 7.20 m of sloping deck. With a 1.5 m top landing, the total structure is 8.70 m long and covers 8.64 m² at 1.20 m wide.

Example 2: A 1,200 mm rise, the same slope

Doubling the rise doubles the run to 14.41 m. That length needs 1 rest landing at the 9 m guide, and the deck area rises to 17.29 m². Long ramps are as much a landscaping project as a carpentry one.

Example 3: A short, steeper 300 mm rise

At a 12.5% slope the ratio is 1:8.0, so a 0.30 m rise needs only 2.40 m of run. Steeper ramps are harder to use and often not permitted for accessibility, even when the geometry works.

What the result means

The slope is the design decision; the run is just its consequence. A 1:12 ramp is the steepest ratio many accessibility standards allow for an unassisted rise, and some standards require a flatter 1:20 for a ramp to count as a walking surface rather than a ramp. The rise limit per run matters because a single continuous slope becomes fatiguing and risky; level landings break the climb. The calculator assumes a straight ramp. Switchbacks reduce the footprint but need landings at each turn and careful headroom. Structure, frost depth, drainage, edge protection, and handrails are separate design questions that a length calculation cannot answer.

Common mistakes

  • Entering the horizontal distance instead of the vertical rise.
  • Confusing a percentage slope with a ratio.
  • Forgetting the level landing at the top.
  • Designing a single run longer than the local maximum rise.
  • Ignoring handrails and edge protection in the width.
  • Assuming a steeper ramp will be acceptable because it fits the space.

Assumptions and limits

  • The ramp is straight and climbs at a constant slope.
  • The rise is measured vertically from the lower surface to the top landing.
  • The top landing is level and included in the total length.
  • The run is horizontal distance, not the sloping surface length.
  • Local accessibility and building rules are checked separately.

Frequently asked questions

What is a 1:12 slope in percent?

One divided by twelve is 0.0833, so 8.33 percent. A 1:20 slope is 5 percent, and a 1:8 slope is 12.5 percent.

How long does a ramp need to be?

Run equals rise divided by slope. For a 600 mm rise at 1:12 the run is 7.2 m, plus any landings. Most standards also cap the rise per run, so longer climbs are split into sections.

Is the run the same as the ramp length?

No. The run is the horizontal distance; the sloping surface is slightly longer because it follows the hypotenuse. The difference is small at gentle slopes but matters when ordering decking.

Do I need landings?

Most accessibility standards require a level landing at the top and bottom, and rest landings on long ramps. They also set minimum landing dimensions, usually at least as deep as the ramp is wide.

Does this calculator check compliance?

No. It calculates geometry only. Maximum slope, rise per run, landing size, handrails, and edge protection are set by local codes and vary by country and building type.

What width should a ramp be?

Check the local standard, which commonly requires a clear width of around 900 to 1,200 mm plus handrails. A wider ramp is easier to pass on but uses more material.

Sources

This is a geometry calculator, not a compliance check. Ramp slope, width, landings, handrails, and edge protection are regulated and vary by jurisdiction. Confirm the requirements with the local building authority before construction.

2026 update

How to use the professional output

This page is not just a formula box. The result is designed to be checked, compared, and taken away.

  • Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
  • A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
  • Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.

The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.

Calccc Editorial Team · Updated 2026-11-18

Prepared by Calccc Editorial Team as an educational estimate. This page is not a licensed professional review and is not financial, medical, legal, or tax advice.

Editorial estimate prepared by the Calccc Editorial Team; not a licensed professional review.