Skip to content

Bike Gear Ratio Calculator

Enter the chainring and cassette teeth, your cadence, and the wheel circumference. The calculator gives the gear ratio, the distance travelled per crank turn, the speed at that cadence, and the traditional gear-inch figure. A 50-tooth chainring and a 16-tooth cog produce a 3.13:1 ratio and about 36.4 km/h at 90 rpm.

Updated 2026-11-19 Editorial estimate Calccc Editorial Team Free · No sign-up
rpm
mm

Measure one full roll of the loaded wheel, or use the tyre size chart. A 700 × 25c road wheel is about 2,155 mm.

Scenarios A/BSave two input sets and compare the results. Stored only in this browser.
AEmpty
BEmpty

Your inputs stay in this browser. No account, no uploads.

Professional worksheet

Detailed schedule & assumptions

Inputs used, method, sensitivity, and any year-by-year table. The summary above stays compact; the audit lives here.

Professional worksheet

Inputs, scope, and sensitivity

Inputs used

Method and scope

Result audit

MetricValue

What this calculator does

A bicycle's gearing is a chain of ratios: the chainring drives the cassette, the cassette turns the wheel, and the wheel turns the road. The first ratio is simply the number of chainring teeth divided by the number of cog teeth. Multiply that by the wheel circumference and you get development, the distance the bike travels for one turn of the cranks. Multiply development by cadence and you get speed. Gear inches express the same relationship against wheel diameter in inches, a unit that predates the metric system but is still used because it makes comparisons between wheel sizes intuitive. This calculator uses a measured wheel circumference in millimetres, which is more accurate than the nominal tyre size, and reports all four figures together so the effect of a gearing change is visible before you buy parts.

How to use it

  1. Count the teeth on the chainring at the front.
  2. Count the teeth on the cassette cog you are using at the back.
  3. Measure the wheel circumference by rolling the loaded bike one revolution.
  4. Enter your usual cadence for the terrain you are riding.
  5. Read the ratio, development, speed, and gear inches.
  6. Compare two combinations before changing chainrings or cassettes.

How it works

Gear ratio = chainring teeth ÷ cassette teeth. Development = ratio × wheel circumference in metres. Speed = development × cadence × 60 ÷ 1,000, in km/h. Gear inches = ratio × wheel diameter in inches, where diameter = circumference ÷ π ÷ 25.4. For 50 ÷ 16 the ratio is 3.13, development is 6.73 m, and speed at 90 rpm is 36.4 km/h.

Example calculations

Example 1: A 50 × 16 road gear

The ratio is 3.13:1, development is 6.73 m per crank turn, and at 90 rpm the speed is 36.4 km/h. Gear inches work out to 84.4, a typical top-end road gear for a strong rider on flat ground.

Example 2: A 34 × 28 climbing gear

The climbing combination gives 1.21:1, 2.62 m per turn, and 11.0 km/h at 70 rpm. That is 32.8 gear inches, low enough to keep the cadence comfortable on a steep gradient without grinding.

Example 3: A 52 × 11 sprint gear

The biggest combination is 4.73:1, with 10.19 m per crank turn and 61.1 km/h at 100 rpm. Gear inches reach 127.7. At that ratio, small cadence changes produce large speed changes, which is why it is reserved for descents and sprints.

What the result means

Gear ratio is the cleanest comparison between setups, but development and speed make it concrete. A ratio of 3.1 means the wheel turns a little more than three times for each crank turn; development translates that into metres, and speed translates it into the number on the computer. Cadence is the variable the rider controls. A lower ratio lets you hold a comfortable cadence on a climb; a higher ratio lets you go faster at the same cadence on a descent. Gear inches remain useful because they normalise for wheel size, so a 700c bike and a 26-inch bike with the same gear inches feel similar. Changing one tooth at the front is a bigger jump than changing one tooth at the back, which is why cassettes offer close ratios and chainrings offer broad ones.

Common mistakes

  • Measuring the wheel with the bike unloaded, so the circumference is too small.
  • Using the nominal tyre size instead of the actual measured circumference.
  • Counting chainring teeth while the chain is on, which is easy to miscount.
  • Mixing gear inches with development and treating them as the same number.
  • Assuming the highest ratio is always faster; it only is if the rider can turn it.
  • Forgetting that cadence, not gearing, is the main control on a climb.

Assumptions and limits

  • The chainring and cassette tooth counts are exact.
  • The wheel circumference is measured with the tyre properly inflated and the rider aboard.
  • There is no slip in the drivetrain.
  • Cadence is steady at the entered value.
  • The bike travels in a straight line on a smooth surface.
  • Gear inches use the standard 25.4 mm per inch conversion.

Frequently asked questions

How do I calculate gear ratio on a bike?

Divide the chainring teeth by the cassette teeth. A 50-tooth chainring and a 16-tooth cog give 50 ÷ 16 = 3.125, usually written 3.13:1. The ratio is independent of wheel size.

What is development?

Development is the distance the bike travels for one turn of the cranks: gear ratio × wheel circumference. It is expressed in metres and is more directly useful than the bare ratio because it includes the wheel.

What are gear inches?

Gear inches are the equivalent diameter of a penny-farthing wheel that would travel the same distance per crank turn: ratio × wheel diameter in inches. They normalise for wheel size and are still used by cyclists.

How do I measure wheel circumference?

Inflate the tyre, sit on the bike, and roll one full revolution with the valve at the bottom. Measure the distance travelled in millimetres. That loaded measurement is more accurate than a nominal tyre chart.

What cadence should I use?

Most riders are comfortable between 80 and 100 rpm on flat roads and lower on steep climbs. Enter the cadence you actually hold, not a target, to see the speed a gear will produce.

Why does one tooth at the front feel bigger than one at the back?

The chainring has fewer total teeth, so one tooth is a larger percentage change. Going from 50 to 51 is a 2% change; going from 16 to 17 at the back is about 6% in the opposite direction, which is a bigger jump.

Sources

This is an educational gearing calculation, not mechanical or coaching advice. Tyre size, wear, and drivetrain condition affect real speed, and gearing should suit the rider and terrain. Confirm compatibility before changing components.

2026 update

How to use the professional output

This page is not just a formula box. The result is designed to be checked, compared, and taken away.

  • Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
  • A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
  • Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.

The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.

Calccc Editorial Team · Updated 2026-11-19

Prepared by Calccc Editorial Team as an educational estimate. This page is not a licensed professional review and is not financial, medical, legal, or tax advice.

Editorial estimate prepared by the Calccc Editorial Team; not a licensed professional review.