What this calculator does
Curtain fabric is bought by length, but the length you need is decided by width. A curtain panel has to be gathered to look right, so the flat fabric is wider than the window by a fullness factor: one and a half times for a light gather, two times for a standard pencil pleat, two and a half for deep pleats or sheers. That gathered width is then split across the panels, and each panel has to fit within the fabric's usable width or be joined with a seam. The drop is the vertical measurement plus hem and heading allowance, and printed fabric has to be rounded up to a whole pattern repeat so the motifs line up. This calculator combines those steps so the fabric order is right the first time.
How to use it
- Measure the track or pole width, not the glass.
- Measure the drop from the track to where you want the curtain to finish.
- Choose a fullness that matches the heading type.
- Set the number of panels, usually two for a window.
- Enter the fabric width and any pattern repeat before ordering.
How it works
Example calculations
Example 1: A 200 cm track with two panels at 2x fullness
The gathered width is 400 cm, so each panel is 200 cm wide. With a 160 cm cut drop, the two panels need 3.20 m of fabric.
Example 2: A wide window with three panels
A 300 cm track at 2.5x fullness gives 750 cm gathered. Three panels are 250 cm each, which fits inside 280 cm fabric, and the total order is 7.05 m.
Example 3: A patterned fabric with a 32 cm repeat
A 265 cm cut drop rounds up to 288 cm to fit whole repeats, adding 46 cm per panel. The order rises to 5.76 m, which is why patterned fabric needs more than plain fabric of the same size.
What the result means
Fullness is the design decision with the biggest effect on cost. Going from 2x to 2.5x adds a quarter more fabric and makes the curtains look fuller when closed, but it also needs a stronger track and more space at each side when open. Panel width is limited by fabric width; if the calculated panel is wider, the panel has to be split and joined, which adds a seam and more length. Pattern repeats can add a surprising amount: a large repeat on a long drop may waste almost a metre per panel. Always round up rather than down, and keep a note of the dye lot so a second order matches.
Common mistakes
- Measuring the glass instead of the track or pole.
- Forgetting hem and heading allowance in the drop.
- Splitting a wide panel without allowing for the seam.
- Ordering patterned fabric without rounding to the repeat.
- Assuming two panels always fit one fabric width.
- Ignoring the extra width needed for curtains to stack clear of the glass.
Assumptions and limits
- The track or pole is mounted where the curtain will hang.
- Fullness is applied to the track width, not the window opening.
- Each panel is cut as a single piece of fabric.
- Hem allowance covers both the top and bottom finish.
- Pattern repeat is measured vertically as printed on the fabric.
Frequently asked questions
What fullness should curtains be?
1.5x for a light gather, 2x for a standard pencil pleat, and 2.5x for deep pleats or sheer fabric. Heavier fabrics often look better with less fullness.
Do I measure the window or the track?
The track or pole. Curtains usually extend beyond the window opening so they can stack clear of the glass and reduce light gaps.
How much extra length do hems need?
About 15 to 20 cm in total for a standard top and bottom finish, more for a deep heading or a lined curtain.
Why does patterned fabric cost more?
Each drop must be a whole number of pattern repeats so the motifs align across panels, which adds length that cannot be used elsewhere.
What if my panel is wider than the fabric?
The panel must be joined with a seam, or you can add more panels. The calculator flags this by showing the panel width against the fabric width.
Should curtains touch the floor?
That is a style choice. A slight break, a hover, or a puddle each change the drop by a few centimetres, so decide before measuring.
Sources
2026 update
How to use the professional output
This page is not just a formula box. The result is designed to be checked, compared, and taken away.
- Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
- A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
- Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.
The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.