Skip to content

Horizontal Tank Volume Calculator

Enter the tank diameter, length, and liquid depth. The calculator handles the circular segment geometry and returns the volume in litres, the full capacity, and the fill percentage. A 1.2 m diameter tank 2.5 m long with 0.5 m of liquid holds 1,115 litres, or 39.4% of its 2,827 litre capacity.

Updated 2026-11-19 Editorial estimate Calccc Editorial Team Free · No sign-up
m
m
m
Scenarios A/BSave two input sets and compare the results. Stored only in this browser.
AEmpty
BEmpty

Your inputs stay in this browser. No account, no uploads.

Professional worksheet

Detailed schedule & assumptions

Inputs used, method, sensitivity, and any year-by-year table. The summary above stays compact; the audit lives here.

Professional worksheet

Inputs, scope, and sensitivity

Inputs used

Method and scope

Result audit

MetricValue

What this calculator does

A horizontal cylindrical tank is one of the most common shapes for fuel oil, water, and process liquids, and its contents are not proportional to depth. The first few centimetres of depth add water across a narrow strip, while the middle of the tank adds water across the full diameter, so the volume curve is S-shaped. Dipsticks and sight glasses read depth, not volume, which is why a conversion formula is needed. This calculator uses the circular segment area at the liquid surface and multiplies by the tank length to give the volume at any depth, along with the full capacity and the remaining empty space. It assumes a level tank with flat ends; dished heads, a tilted installation, or internal fittings change the result and need a different calculation.

How to use it

  1. Enter the inside diameter of the cylindrical shell.
  2. Enter the inside length between the flat ends.
  3. Enter the liquid depth measured vertically from the bottom.
  4. Read the volume in litres and the percentage full.
  5. Compare the fill percentage with the depth percentage.
  6. Recheck with the tank's calibration chart if one is available.

How it works

Radius r = diameter / 2. Liquid cross-section area A = r² × arccos((r - h) / r) - (r - h) × √(2rh - h²), where h is the liquid depth. Volume = A × length. Full capacity = π × r² × length. Fill percentage = volume / capacity × 100. In the default case: r = 0.6 m, h = 0.5 m, A = 0.4460 m², volume = 0.4460 × 2.5 = 1.115 m³ = 1,115 L, capacity = 2,827 L, fill = 39.4%.

Example calculations

Example 1: Half full

A 1.2 m diameter tank holding 0.6 m of liquid is exactly half full. The formula returns half the capacity, 1,414 litres, and 50%. At the half-full point the volume is proportional to depth again, but above and below it the relationship curves away in opposite directions.

Example 2: A shallow dip

The same tank with only 0.1 m of liquid holds about 92 litres, or 3.3% of capacity, even though the depth is 8.3% of the diameter. A dipstick reading near the bottom can look reassuring while the tank is nearly empty, which is why the conversion matters for delivery planning.

Example 3: Nearly full

At 1.1 m of depth the same tank holds about 2,735 litres, or 96.7% of capacity, when the depth is 91.7% of the diameter. The curve flattens near the top just as it does near the bottom. Filling to a percentage of depth rather than a volume target can overfill or underfill a delivery.

What the result means

The depth-to-volume curve is the practical point. Near the bottom and near the top, a small change in depth produces a small change in volume; in the middle, the same change produces the largest volume change. That is why a dipstick near the half-full mark is most sensitive and why a float gauge can appear to move slowly at the extremes. The formula assumes a cylinder with flat ends and a level tank. Tanks with dished or domed ends hold more than a flat-ended cylinder of the same length, sometimes by several percent, and a tank on a slope reads differently from a level one. For custody transfer or compliance, use the tank's certified calibration table rather than a generic formula.

Common mistakes

  • Treating volume as a linear function of depth.
  • Measuring depth in centimetres but entering metres without converting.
  • Using the outside diameter instead of the inside diameter.
  • Ignoring the extra volume in dished ends.
  • Assuming a tilted tank reads the same as a level one.
  • Using the formula as a substitute for a certified calibration chart.

Assumptions and limits

  • The tank is a right circular cylinder with flat ends.
  • The tank is level and not deformed.
  • The liquid depth is measured vertically from the lowest point inside the shell.
  • The liquid fills the full circular cross-section at the measured depth.
  • No internal partitions, baffles, or heating coils displace liquid.
  • The liquid density does not affect the volume calculation.

Frequently asked questions

Why is a horizontal tank not linear in depth?

Because the width of the liquid surface changes with depth. Near the bottom the surface is a narrow strip, so each centimetre adds little volume; near the middle the surface spans the full diameter, so each centimetre adds much more.

How do I convert the result to other units?

One cubic metre is 1,000 litres, and one litre is 0.001 cubic metres. To convert to gallons, multiply litres by 0.2642 for US gallons or 0.2200 for imperial gallons. Keep the length unit consistent when entering the dimensions.

Does the tank end shape matter?

Yes. A dished or domed end adds volume beyond a flat-ended cylinder of the same length, often a few percent. For accurate inventory, use the manufacturer's capacity table or include the end volume in the calculation.

What if the tank is tilted?

A tilted tank holds a different volume at the same dip reading, and the difference grows as the slope increases. The formula here assumes a level tank. For a tilted tank, use a calibration chart prepared for that installation.

Can I use this for a tank with a rounded bottom?

Not directly. A rounded or elliptical bottom changes the cross-section shape. The method is the same but the area formula is different, so use the geometry that matches the tank.

How accurate is the formula?

It is exact for an ideal flat-ended cylinder at a level attitude. Real tanks have welds, fittings, and slight deformation, so measured capacity can differ by a small percentage. For billing or compliance, use a certified calibration.

Sources

This calculator is an educational planning tool, not financial, legal, insurance, medical, or professional advice. Results depend on the inputs and on rules that vary by place and provider. Confirm important decisions with a qualified professional and the relevant documents.

2026 update

How to use the professional output

This page is not just a formula box. The result is designed to be checked, compared, and taken away.

  • Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
  • A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
  • Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.

The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.

Calccc Editorial Team · Updated 2026-11-19

Prepared by Calccc Editorial Team as an educational estimate. This page is not a licensed professional review and is not financial, medical, legal, or tax advice.

Editorial estimate prepared by the Calccc Editorial Team; not a licensed professional review.