Key takeaways
- ρ = m ÷ V. Density is mass per unit volume, not weight.
- 1 g/cm³ = 1,000 kg/m³ = 1 kg/L exactly. The metric ladder is a factor of 1,000.
- 1 lb/ft³ = 16.018463 kg/m³. 1 lb/in³ = 27,679.9047 kg/m³, or 1,728 times larger.
- Convert through a common base. Multiply by the from-factor, divide by the to-factor.
- Gases need conditions. A density without temperature and pressure is incomplete.
- Bulk density is not material density. Packing and voids change the number.
Density is mass per unit volume
Density is how much mass sits in a given volume: ρ = m ÷ V. In SI, mass is in kilograms and volume in cubic meters, so density is kg/m³. A cubic meter of water has a mass of about 1,000 kg, which is why water’s density is quoted as 1,000 kg/m³ or 1 g/cm³.
Density is not weight. Weight depends on gravity; mass does not. A 1 kg block has the same mass on the Moon but a lower weight. Specific gravity avoids units altogether: it is the ratio of a material’s density to the density of water at 4 °C, so a specific gravity of 7.85 means 7.85 times the density of water. That is convenient in engineering but easy to confuse with density itself.
The formulas assume a uniform material. A sealed brick, a bowl of cereal, and a bag of sand are not uniform at every scale, which is why bulk density gets its own treatment later.
The metric ladder is a factor of 1,000
Metric density units form a clean ladder because 1 cm³ is 0.001 L and 1 g is 0.001 kg. One gram per cubic centimeter is therefore 0.001 kg ÷ 0.000001 m³ = 1,000 kg/m³. One kilogram per liter is 1 kg ÷ 0.001 m³ = 1,000 kg/m³ as well, so 1 g/cm³ = 1 kg/L = 1,000 kg/m³.
The same relationships make grams per liter equal to kilograms per cubic meter: 1 g/L = 1 kg/m³. That unit is common for gases and for concentrations in water. A reading of 1.225 kg/m³ is 1.225 g/L, not 1,225 g/L.
| Unit | Factor to kg/m³ | Typical use |
|---|---|---|
| kg/m³ | 1 | SI base for density; engineering and science |
| g/cm³ | 1,000 | Laboratory solids and liquids |
| g/L | 1 | Gases and water concentrations |
| kg/L | 1,000 | Liquids in bulk |
The first three factors are exact by definition; no measurement is involved.
Where the imperial factors come from
Imperial density factors come from two exact definitions: 1 pound = 0.45359237 kg, and 1 foot = 0.3048 m. A cubic foot is 0.3048³ = 0.028316846592 m³. Dividing the mass of one pound by that volume gives 0.45359237 ÷ 0.028316846592 = 16.018463 kg/m³ per lb/ft³.
A cubic inch is 0.3048³ ÷ 1,728 = 0.000016387064 m³, so one pound per cubic inch is 0.45359237 ÷ 0.000016387064 = 27,679.9047 kg/m³. That is 1,728 times the lb/ft³ factor, because a cubic foot holds 1,728 cubic inches.
| Unit | Factor to kg/m³ | Relationship |
|---|---|---|
| lb/ft³ | 16.018463 | 1 lb ÷ 0.028316846592 m³ |
| lb/in³ | 27,679.9047 | 16.018463 × 1,728 |
US construction, shipping, and some engineering tables use lb/ft³, while laboratory work uses g/cm³ and international specifications use kg/m³. The three are not interchangeable without the factor.
The conversion formula
The converter routes every input through kg/m³. Convert the value to kilograms per cubic meter by multiplying by the factor for the unit you have, then divide by the factor for the unit you want: result = value × factor(from) ÷ factor(to).
Example: 2.7 g/cm³ to lb/ft³. 2.7 × 1,000 = 2,700 kg/m³. 2,700 ÷ 16.018463 = 168.56 lb/ft³. Going the other way, 168.56 × 16.018463 = 2,700 kg/m³, then ÷ 1,000 = 2.7 g/cm³.
Because the chain passes through a common unit, any pair of units works without a dedicated factor. That also makes errors easier to spot: a result that changes by a factor of 1,000 usually means g/cm³ and kg/m³ were mixed.
Worked examples
Water: 1 g/cm³. 1,000 kg/m³. In imperial units, 1,000 ÷ 16.018463 = 62.43 lb/ft³. In lb/in³, 1,000 ÷ 27,679.9047 = 0.0361.
Steel: 7.85 g/cm³. 7,850 kg/m³, or 490.06 lb/ft³, or 0.2836 lb/in³.
Air at sea level and 15 °C: 1.225 kg/m³. 0.001225 g/cm³, or 0.0765 lb/ft³. The small numbers are a reminder that gas density is roughly a thousandth of liquid density.
Concrete: 2,400 kg/m³. 2.4 g/cm³, or 149.83 lb/ft³.
Gold: 19.32 g/cm³. 19,320 kg/m³, or 1,206.1 lb/ft³. Gold is dense enough that a small volume carries a lot of mass.
Gasoline: about 0.74 g/cm³. 740 kg/m³, or 46.2 lb/ft³. The exact value varies with blend and temperature.
Temperature and pressure change the number
For solids and liquids, density changes slowly with temperature and pressure. Water is the familiar exception near freezing: it reaches its maximum density of about 999.97 kg/m³ at 4 °C, and its density at 20 °C is about 998.2 kg/m³. That is why a water density quoted as exactly 1,000 kg/m³ is a rounded reference value, not a universal constant.
Gases change far more. The ideal gas law gives ρ = pM ÷ (RT), where p is absolute pressure, M is molar mass, R is 8.314 J/(mol·K), and T is absolute temperature. Air at 101.325 kPa and 15 °C works out to about 1.225 kg/m³; at 0 °C it is about 1.293 kg/m³, and at 30 °C about 1.165 kg/m³. A 15 °C change moves the number by roughly 10%.
So a gas density without temperature and pressure is incomplete. Compressed-gas tables usually state a reference condition, and conversion between conditions requires the gas law, not just a unit factor.
Bulk, particle, and apparent density
Bulk density includes the voids between particles. Dry sand might be about 1,600 kg/m³ loose and 1,900 kg/m³ compacted, while the density of the individual quartz grains is about 2,650 kg/m³. The material did not change; the packing did. Grain, powder, mulch, and pellets all behave this way, and shipping and storage calculations usually need bulk density.
Particle density, sometimes called true or skeletal density, excludes the voids between particles but may include internal pores, depending on the method. Apparent density adds another variation. Specific gravity is a ratio, not a density, and is dimensionless.
The converter does not know which one you have. If you are converting a value for a powder or aggregate, confirm whether the source measured loose, tapped, or compacted material, and keep that condition with the number.
Common mistakes
Using g/cm³ and kg/m³ as the same scale. The difference is a factor of 1,000, which turns a plausible answer into one that is wrong by three orders of magnitude.
Rounding 16.018463 to 16. The shortcut is about 0.1% low, which is fine for an estimate but not for a specification.
Mixing lb/ft³ and lb/in³. The factor between them is 1,728. A density of 0.28 lb/in³ is about 490 lb/ft³, not 0.28 lb/ft³.
Converting a gas density without conditions. A value at 0 °C and a value at 30 °C describe different amounts of mass in the same volume.
Reporting density as weight. A cubic meter of concrete has the same density on the Moon; its weight is lower.
Treating specific gravity as kg/m³. Specific gravity is a dimensionless ratio. Multiply by 1,000 to get kg/m³ for water-based comparisons.
Precision and rounding
Carry the published factor to at least six significant figures, then round the answer to the precision of the input. A density measured as 7.85 g/cm³ has three significant figures, so 490 lb/ft³ is honest and 490.06 is overstating the measurement. The conversion factor itself is not the limiting factor.
Tolerances scale with the same factor. A ±2% density tolerance stays ±2% after conversion, because the factor is a constant. Do not add percentage errors from the factor unless the factor itself is an estimate.
Display rounding can hide a real difference: 1.000 and 1.004 g/cm³ both show as 1.000 at three decimals, yet the second is 4 kg/m³ denser. Keep more digits in intermediate steps than you show.
Frequently asked questions
How many kg/m³ are in 1 g/cm³?
Exactly 1,000. The centimeter is one hundredth of a meter, so a cubic centimeter is one millionth of a cubic meter, and a gram is one thousandth of a kilogram.
How do I convert kg/m³ to lb/ft³?
Divide by 16.018463. For example, 2,400 kg/m³ ÷ 16.018463 = 149.83 lb/ft³.
Is 1 g/cm³ the same as 1 kg/L?
Yes. Both equal 1,000 kg/m³, so a liter of water has a mass of about 1 kg.
Why does density change with temperature?
Most materials expand when heated, so the same mass occupies more volume and the density falls. Gases change much more than liquids or solids.
What is the difference between density and specific gravity?
Density has units such as kg/m³. Specific gravity is a dimensionless ratio to the density of water, so a specific gravity of 1.0 corresponds to about 1,000 kg/m³.
Which density does the converter use?
Whichever value you enter. It converts units but does not adjust for temperature, pressure, or the difference between bulk and particle density.
Further reading