Skip to content

Plaster Calculator

Enter the wall or ceiling area, the thickness per coat, and the number of coats. The calculator multiplies area by thickness and coats, applies density and waste, and reports plaster weight, bag count, water, and the area one bag covers.

Updated 2026-11-18 Editorial estimate Calccc Editorial Team Free · No sign-up
m²
mm
%
Advanced options
kg/m³

About 1,200 kg/m³ for gypsum plaster; cement render is heavier.

kg
L/kg
Scenarios A/BSave two input sets and compare the results. Stored only in this browser.
AEmpty
BEmpty

Your inputs stay in this browser. No account, no uploads.

Professional worksheet

Detailed schedule & assumptions

Inputs used, method, sensitivity, and any year-by-year table. The summary above stays compact; the audit lives here.

Professional worksheet

Inputs, scope, and sensitivity

Inputs used

Advanced inputs used

Method and scope

Result audit

MetricValue

What this calculator does

Plaster quantity depends on area, thickness, and the number of coats, and the difference between a single skim and a three-coat render can be several times the material. Gypsum plaster, cement render, and lime plaster also differ in density and water demand, so the product data sheet matters more than a generic rule of thumb. This calculator converts area and thickness into volume, then weight and bags, and estimates water from the chosen ratio. It also shows the coverage of one bag at the chosen thickness, which is handy for checking a supplier's claim. It is an estimate for ordering, not a specification of the plaster system.

How to use it

  1. Measure the wall or ceiling area to be plastered.
  2. Enter the thickness of one coat in millimetres.
  3. Choose the number of coats in the specified system.
  4. Set the plaster density and bag size from the product data.
  5. Add a waste allowance for uneven surfaces and mixing losses.

How it works

Volume = area x thickness / 1,000 x coats x (1 + waste). Weight = volume x density. Bags = weight / bag size, rounded up. In the default case, 40.0 m² at 10 mm in 2 coats needs 1,056.0 kg, or 43 bags of 25 kg, and about 633.6 L of water.

Example calculations

Example 1: 40 m² in two 10 mm coats

The volume including waste is 0.880 m³, which weighs 1,056.0 kg and requires 43 bags. Each bag covers about 2.08 m² at this thickness, so the order is consistent with the area.

Example 2: A small 12.5 m² patch in one 5 mm coat

A thin single coat needs only 82.5 kg, or 4 bags, and 49.5 L of water. Small jobs are dominated by the minimum bag size, so the rounded count matters more than the precise weight.

Example 3: 100 m² in three 15 mm coats

Thick multi-coat work scales quickly: 5,940.0 kg, or 238 bags, and 3,564.0 L of water. At this scale, delivery and mixing logistics matter as much as the material quantity.

What the result means

The estimate assumes a flat, even substrate and a consistent thickness. Real walls vary, and dubbing out hollows or building up corners can add a lot of material. Different plaster systems also have different densities and application thicknesses, so use the manufacturer's coverage figure where one is available. Water is a guide: add it gradually and follow the product instructions, because over-watering weakens the set. Bags should be ordered with a small surplus, and unused bags should be kept dry because plaster absorbs moisture from the air.

Common mistakes

  • Using the finish-coat thickness for the whole system.
  • Forgetting to allow for uneven walls and dubbing out.
  • Using a generic density instead of the product data.
  • Adding too much water and reducing the strength of the set.
  • Ordering exact bag counts with no allowance for breakage.

Assumptions and limits

  • The area is measured flat and includes openings unless deducted.
  • Each coat has the same nominal thickness.
  • The density and bag size match the product supplied.
  • The water ratio is a starting point for mixing.
  • The substrate is sound and does not require extensive preparation.

Frequently asked questions

How thick should plaster be?

It depends on the system. A gypsum finish coat is often 2 to 5 mm, while a backing coat or cement render can be 10 to 15 mm. The number of coats and the total thickness should follow the specification or the manufacturer's instructions.

How many coats are needed?

Two coats are common for a flat finish: a backing coat and a finish coat. Three coats may be used where extra flatness or durability is required. A single thin coat is suitable only for small patches or specific products.

Should I deduct windows and doors?

For a quick estimate, deduct large openings and add a little back for the reveals. For a precise order, measure the actual plastered area, including returns and reveals, rather than the nominal wall area.

Why is the water volume so large?

Plaster is mixed with a significant amount of water to make it workable, and the ratio in the calculator is per kilogram of dry plaster. The exact demand depends on the product and the substrate, so add water gradually.

Can I use this for cement render?

Yes, if you set the density and water ratio for the render system. Cement render is denser than gypsum plaster and may include sand, so the bag count and water demand will differ.

What is coverage per bag?

It is the area one bag covers at the entered thickness, calculated as bag size divided by density and thickness. It is a useful cross-check against the supplier's published coverage.

Sources

This calculator is an educational materials estimate. It does not specify a plaster system or replace product instructions. Confirm density, thickness, and coverage with the manufacturer before ordering.

2026 update

How to use the professional output

This page is not just a formula box. The result is designed to be checked, compared, and taken away.

  • Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
  • A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
  • Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.

The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.

Calccc Editorial Team · Updated 2026-11-18

Prepared by Calccc Editorial Team as an educational estimate. This page is not a licensed professional review and is not financial, medical, legal, or tax advice.

Editorial estimate prepared by the Calccc Editorial Team; not a licensed professional review.