What this calculator does
Plaster quantity depends on area, thickness, and the number of coats, and the difference between a single skim and a three-coat render can be several times the material. Gypsum plaster, cement render, and lime plaster also differ in density and water demand, so the product data sheet matters more than a generic rule of thumb. This calculator converts area and thickness into volume, then weight and bags, and estimates water from the chosen ratio. It also shows the coverage of one bag at the chosen thickness, which is handy for checking a supplier's claim. It is an estimate for ordering, not a specification of the plaster system.
How to use it
- Measure the wall or ceiling area to be plastered.
- Enter the thickness of one coat in millimetres.
- Choose the number of coats in the specified system.
- Set the plaster density and bag size from the product data.
- Add a waste allowance for uneven surfaces and mixing losses.
How it works
Example calculations
Example 1: 40 m² in two 10 mm coats
The volume including waste is 0.880 m³, which weighs 1,056.0 kg and requires 43 bags. Each bag covers about 2.08 m² at this thickness, so the order is consistent with the area.
Example 2: A small 12.5 m² patch in one 5 mm coat
A thin single coat needs only 82.5 kg, or 4 bags, and 49.5 L of water. Small jobs are dominated by the minimum bag size, so the rounded count matters more than the precise weight.
Example 3: 100 m² in three 15 mm coats
Thick multi-coat work scales quickly: 5,940.0 kg, or 238 bags, and 3,564.0 L of water. At this scale, delivery and mixing logistics matter as much as the material quantity.
What the result means
The estimate assumes a flat, even substrate and a consistent thickness. Real walls vary, and dubbing out hollows or building up corners can add a lot of material. Different plaster systems also have different densities and application thicknesses, so use the manufacturer's coverage figure where one is available. Water is a guide: add it gradually and follow the product instructions, because over-watering weakens the set. Bags should be ordered with a small surplus, and unused bags should be kept dry because plaster absorbs moisture from the air.
Common mistakes
- Using the finish-coat thickness for the whole system.
- Forgetting to allow for uneven walls and dubbing out.
- Using a generic density instead of the product data.
- Adding too much water and reducing the strength of the set.
- Ordering exact bag counts with no allowance for breakage.
Assumptions and limits
- The area is measured flat and includes openings unless deducted.
- Each coat has the same nominal thickness.
- The density and bag size match the product supplied.
- The water ratio is a starting point for mixing.
- The substrate is sound and does not require extensive preparation.
Frequently asked questions
How thick should plaster be?
It depends on the system. A gypsum finish coat is often 2 to 5 mm, while a backing coat or cement render can be 10 to 15 mm. The number of coats and the total thickness should follow the specification or the manufacturer's instructions.
How many coats are needed?
Two coats are common for a flat finish: a backing coat and a finish coat. Three coats may be used where extra flatness or durability is required. A single thin coat is suitable only for small patches or specific products.
Should I deduct windows and doors?
For a quick estimate, deduct large openings and add a little back for the reveals. For a precise order, measure the actual plastered area, including returns and reveals, rather than the nominal wall area.
Why is the water volume so large?
Plaster is mixed with a significant amount of water to make it workable, and the ratio in the calculator is per kilogram of dry plaster. The exact demand depends on the product and the substrate, so add water gradually.
Can I use this for cement render?
Yes, if you set the density and water ratio for the render system. Cement render is denser than gypsum plaster and may include sand, so the bag count and water demand will differ.
What is coverage per bag?
It is the area one bag covers at the entered thickness, calculated as bag size divided by density and thickness. It is a useful cross-check against the supplier's published coverage.
Sources
2026 update
How to use the professional output
This page is not just a formula box. The result is designed to be checked, compared, and taken away.
- Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
- A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
- Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.
The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.