What this calculator does
Air changes per hour, or ACH, is the number of times the full volume of a room is replaced by outside or conditioned air in one hour. It is used for ventilation checks, bathroom and kitchen extract sizing, and indoor air quality planning. The arithmetic is simple, but the result is only as good as the airflow figure: a fan's datasheet rating is not the same as the air it actually moves through a real duct and a real room. This calculator converts room dimensions into volume, divides the airflow by that volume, and adds the minutes per air change and airflow per floor area. Use it to check a design target or a fan specification, then confirm the installed airflow with a measurement or the manufacturer's system curve.
How to use it
- Measure the room length, width, and ceiling height in metres.
- Enter the ventilation airflow in cubic metres per hour.
- Read the air changes per hour and the minutes per air change.
- Compare the result with the target in your local code or design brief.
- Check whether the airflow figure is for the fan or for the installed system.
- Investigate dead zones, duct losses, and transfer gaps if the result is borderline.
How it works
Example calculations
Example 1: A 5 × 4 m room
A room 5 m long, 4 m wide, and 2.7 m high has a volume of 54 m³. At 180 m³/h of ventilation, the air changes per hour are 3.33, or one full change every 18 minutes. The airflow per floor area is 9 m³/h per m². Whether 3.33 ACH is enough depends on the room's use and the local target.
Example 2: A larger room with the same result
A 6 × 5 m room with a 3 m ceiling has 90 m³ of volume. At 270 m³/h, the result is exactly 3.00 ACH and 20 minutes per change. The room is larger and the airflow is higher, but the air-exchange rate is lower. This shows why volume, not just floor area, drives the calculation.
Example 3: A small bathroom
A 3 × 3 m bathroom with a 2.4 m ceiling has 21.6 m³ of volume. An extract fan moving 108 m³/h gives 5.00 ACH and a full change every 12 minutes. Small rooms reach high ACH with modest airflow, which is why bathroom and kitchen extract rates are often specified as airflow rather than ACH.
What the result means
The ACH figure describes air exchange, not air quality. A high number does not guarantee good mixing or fresh air in every corner, and a low number does not prove a room is unhealthy. The minutes-per-change figure is often easier to picture: 3.33 ACH means a complete change every 18 minutes. The airflow per floor area is a useful cross-check when comparing rooms of different heights. Use the target from your building code or a ventilation designer, and treat the datasheet airflow as an upper bound until the installed system is measured.
Common mistakes
- Using the fan's free-air rating instead of the installed system airflow.
- Multiplying floor area by a assumed height instead of measuring the ceiling.
- Mixing cubic metres and cubic feet in the same calculation.
- Assuming a high ACH means the air is well mixed throughout the room.
- Forgetting that extract ventilation needs a make-up air path.
- Applying a residential target to a commercial or specialty space without checking the code.
Assumptions and limits
- The room is a simple rectangular box with a flat ceiling.
- The airflow figure represents the air actually moving through the room.
- The air is fully mixed, which is an idealisation.
- No allowance is made for furniture, partitions, or dead zones.
- The ventilation rate is constant over the hour.
- Local code targets and occupancy requirements are not applied automatically.
Frequently asked questions
What does 3 ACH mean?
It means the equivalent of the room's full volume of air is replaced three times per hour, or once every 20 minutes. It is a rate, not a guarantee that every part of the room receives fresh air equally.
How do I find the ventilation airflow?
Use the fan or ventilation unit datasheet, then adjust for duct length, filters, and fittings. For an existing system, a calibrated flow hood or anemometer measurement is more reliable than a label.
Is ACH based on floor area or volume?
Volume. The room length, width, and ceiling height are multiplied together. Two rooms with the same floor area but different ceiling heights have different volumes and therefore different ACH for the same airflow.
What ACH should a bathroom have?
Targets vary by code and by whether the fan is intermittent or continuous. Many residential codes specify bathroom extract airflow rather than ACH. Check the local requirement and the fan's installed performance.
Does opening a window count as ventilation?
It can, but the airflow is uncontrolled and depends on weather and temperature. A calculated ACH assumes a known airflow; an open window does not provide a reliable number.
Can I use this for a whole house?
You can apply the same arithmetic to a whole-house volume and a whole-house ventilation rate, but the result is a simple average. Room-by-room air distribution, transfer grilles, and envelope leakage need a proper ventilation design.
Sources
2026 update
How to use the professional output
This page is not just a formula box. The result is designed to be checked, compared, and taken away.
- Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
- A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
- Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.
The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.