What this calculator does
Dew point is the temperature at which air becomes saturated and water starts to condense. It is a more direct measure of moisture than relative humidity, because relative humidity changes with temperature even when the amount of water vapour stays the same. For construction and finishing work, the dew point tells you whether a surface is likely to stay wet: if a wall, window, or slab is at or below the dew point, condensation can form. This calculator uses the Magnus approximation to convert temperature and relative humidity into dew point, and it also shows the dew point depression, vapour pressure, and absolute humidity. It is a planning and diagnostic aid for painting, plastering, concrete, and ventilation, not a weather forecast.
How to use it
- Measure the air temperature near the surface you are checking.
- Measure the relative humidity in the same air.
- Enter both values and read the dew point.
- Compare the dew point with the surface temperature.
- Check the depression: a small gap means condensation is close.
- Ventilate, heat, or dehumidify before painting, plastering, or sealing.
How it works
Example calculations
Example 1: 22 °C and 60% humidity
At 22 °C and 60% relative humidity, the dew point is about 13.9 °C. The depression is 8.1 °C, so a surface above roughly 14 °C should stay dry. The actual vapour pressure is about 15.82 hPa and the absolute humidity is about 11.6 g/m³.
Example 2: A humid 30 °C room
At 30 °C and 80% humidity, the dew point rises to about 26.2 °C and the depression is only 3.8 °C. A cool floor, a cold water pipe, or an air-conditioned surface below 26 °C can condense water. High absolute humidity also means ventilation and dehumidification have more work to do.
Example 3: Cold air at 5 °C
At 5 °C and 40% humidity, the dew point is about -7.5 °C, with a 12.5 °C depression. The air is cold but not very humid in absolute terms. If that air leaks into a warmer room, its relative humidity falls as it warms, which is why winter indoor air can feel dry.
What the result means
The dew point is the surface temperature to watch. If a surface is below it, condensation is possible; the closer the surface is to the dew point, the more likely it is. The depression tells you the margin: a small depression means a small temperature drop can tip the surface into condensation. Absolute humidity is useful when comparing air masses, because it does not change when air is simply heated or cooled. Use the result to decide whether to ventilate, heat, or dehumidify, and to check whether a planned coating or adhesive can cure before moisture forms. The Magnus formula is an approximation; for critical work, use a calibrated hygrometer and the manufacturer's conditions.
Common mistakes
- Confusing dew point with relative humidity; they are different quantities.
- Using a room-temperature reading when the surface is much colder.
- Assuming a warm room cannot condense water on a cold surface.
- Painting or plastering when the surface is close to the dew point.
- Ignoring the effect of ventilation on local humidity.
- Treating the dew point as a weather forecast rather than a moisture calculation.
Assumptions and limits
- The air temperature and relative humidity are measured in the same location.
- The Magnus approximation is adequate for the temperature range used.
- The surface temperature is known or can be measured separately.
- No condensation nuclei, salts, or surface effects change the dew point.
- The air is not supersaturated.
- The calculation is for general planning, not a calibration-grade psychrometric analysis.
Frequently asked questions
What is the dew point?
It is the temperature at which air becomes saturated with water vapour and condensation begins. If a surface is at or below the dew point, water can form on it.
What is a comfortable dew point?
There is no single number, but a dew point around 10 to 16 °C is often comfortable indoors. Above roughly 18 to 20 °C, the air can feel muggy. Comfort also depends on temperature, airflow, and clothing.
Why does the dew point matter for painting?
Paint and coatings need the surface to stay above the dew point while they cure. If the surface is colder, condensation can form and cause poor adhesion, blushing, or a failed finish. Check both the air and surface temperature.
Can the dew point be higher than the air temperature?
No. The dew point is always at or below the air temperature. If the air is saturated, the two are equal. A calculation that gives a higher value usually means the humidity input or the formula range is wrong.
Does heating air lower the dew point?
Heating air lowers its relative humidity but does not change its absolute moisture content, so the dew point stays the same. That is why heating alone does not remove moisture; ventilation or dehumidification does.
How accurate is this calculator?
The Magnus approximation is accurate to a fraction of a degree over normal indoor and outdoor temperatures. For critical measurements, use a calibrated instrument and the manufacturer's or a psychrometric chart's values.
Sources
2026 update
How to use the professional output
This page is not just a formula box. The result is designed to be checked, compared, and taken away.
- Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
- A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
- Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.
The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.