Skip to content

Cycling Speed From Power Calculator

Enter sustained power, rider and bike weight, road grade, and optional drag and rolling-resistance values. The calculator solves the power equation for speed. With 200 W moving 80 kg on the flat at a drag area of 0.32 m², the estimated speed is about 33.9 km/h and a 40 km ride takes about 1 hour 11 minutes.

Updated 2026-11-19 Editorial estimate Calccc Editorial Team Free · No sign-up
W
kg
%

Positive is uphill, negative is downhill. 0 is flat.

Advanced options

About 0.004 on smooth asphalt with good tyres and 0.008 or more on rough roads.

m²

0.25-0.30 for a racing position, 0.35-0.45 for an upright position.

kg/m³

About 1.226 at sea level and 15 °C; lower at altitude or in heat.

Scenarios A/BSave two input sets and compare the results. Stored only in this browser.
AEmpty
BEmpty

Your inputs stay in this browser. No account, no uploads.

Professional worksheet

Detailed schedule & assumptions

Inputs used, method, sensitivity, and any year-by-year table. The summary above stays compact; the audit lives here.

Professional worksheet

Inputs, scope, and sensitivity

Inputs used

Advanced inputs used

Method and scope

Result audit

MetricValue

What this calculator does

On a bicycle, almost all of the power you produce goes into three things: rolling resistance, gravity, and aerodynamic drag. Rolling resistance is roughly constant, gravity depends on the grade, and drag grows with the square of speed, which is why the last few kilometres per hour are so expensive. This calculator takes a sustained power figure and solves for the speed it supports, then shows how the power splits between those three losses. It is useful for planning a time on a known route, for understanding why a headwind or a hill costs so much, and for comparing positions or equipment changes. The inputs include estimates for drag area and rolling resistance, and the answer is only as good as those estimates. Treat the result as a planning figure, not a prediction of a real ride with wind, traffic, and fatigue.

How to use it

  1. Enter the power you can sustain for the duration of the ride.
  2. Enter the combined weight of rider, bike, and luggage.
  3. Set the road grade, using 0 for flat and positive numbers for climbs.
  4. Adjust rolling resistance for the surface and tyre type.
  5. Adjust drag area for your position and equipment.
  6. Read the speed, the 40 km time, and the share of power lost to each resistance.

How it works

Power = speed × (Crr × mass × g × cos θ + mass × g × sin θ + 0.5 × air density × CdA × speed²), where θ is the slope angle from the grade, Crr is rolling resistance, CdA is drag area, and g is 9.81 m/s². The calculator solves this equation for speed. In the default case at 0% grade: 200 W = v × (0.005 × 80 × 9.81 + 0.5 × 1.226 × 0.32 × v²), which gives v = 9.40 m/s, or 33.9 km/h.

Example calculations

Example 1: 200 W on the flat

An 80 kg rider and bike at 200 W on smooth asphalt with a CdA of 0.32 m² reaches about 33.9 km/h. About 82% of the power goes into aerodynamic drag and 18% into rolling resistance. A 40 km ride at that speed takes about 1 hour 11 minutes. Sitting up to a CdA of 0.40 m² would cut the speed to roughly 31 km/h.

Example 2: A 5% climb

The same rider and power on a 5% grade fall to about 11 km/h. Gravity now takes more than half of the power, rolling resistance takes a small share, and drag becomes minor because speed is low. This is why climbing speed is dominated by power-to-weight and why losing a kilogram matters far more uphill than on the flat.

Example 3: More power, less speed gain

Raising power from 200 W to 250 W on the flat increases speed from about 33.9 km/h to about 36.5 km/h, roughly 7.7%. Because drag rises with the cube of speed, a 25% power increase buys far less than a 25% speed increase. On a climb, where gravity dominates, the same power increase translates into a much larger percentage speed gain.

What the result means

The speed split tells you where to invest effort. On the flat, most of the power goes into drag, so position, clothing, and wheels dominate. On a climb, gravity dominates, so weight and sustained power-to-weight matter most. Rolling resistance is small but constant, and it matters more at low speeds and on rough surfaces. The model uses a steady state: acceleration, corners, braking, and wind are excluded, so real average speed on a route will usually be lower than the flat-road estimate. CdA in particular is difficult to estimate without testing, and a small change in position can move it by 10% or more. Use the calculator for direction and sensitivity, and use a power meter and a known route for calibration.

Common mistakes

  • Using average power for a ride with long stops, which overstates speed.
  • Entering rider weight only and forgetting the bike, bottles, and luggage.
  • Treating CdA as a fixed constant across different positions.
  • Ignoring wind, which changes the effective air speed and drag.
  • Comparing speeds from different tyre pressures or surfaces.
  • Expecting speed to rise in proportion to power on flat roads.

Assumptions and limits

  • Power is held steady for the whole duration.
  • The road is smooth and dry, with no wind or drafting.
  • CdA, rolling resistance, and air density are constant and correctly estimated.
  • The rider holds one position for the entire ride.
  • Acceleration, braking, corners, and traffic are ignored.
  • The result is a steady-state model, not a race prediction.

Frequently asked questions

Why does speed not double when power doubles?

Aerodynamic drag rises with the square of speed, so the power needed to overcome it rises with the cube. Doubling speed on the flat requires roughly eight times the power. That is why gains get smaller as speed rises.

What is CdA?

CdA is the product of the drag coefficient and the frontal area, expressed in square metres. It summarises how aerodynamic a rider and bike are. A racing position can be around 0.25 m², while an upright position can exceed 0.40 m².

How accurate is the estimated speed?

It is typically within a few km/h on flat roads if CdA, weight, and power are accurate. Wind, road surface, and position changes during the ride account for most of the difference between the model and a real average.

What rolling resistance should I use?

About 0.004 to 0.006 on smooth asphalt with good tyres, and 0.008 or more on coarse or wet surfaces. Wider tyres at lower pressure can be faster on rough roads than narrow tyres at high pressure.

Does the calculator account for wind?

No. Wind changes the air speed the rider experiences, and a headwind is much more costly than the same tailwind is helpful. For a rough adjustment, change the air density or treat the headwind component as extra speed in the drag term.

Can I use this for an e-bike?

Yes, if you enter the combined motor and rider power and the total system weight. The model does not include battery limits, motor cut-off speed, or assist behaviour, so treat the result as the steady speed the total power supports.

Sources

This calculator is an educational planning tool, not financial, legal, insurance, medical, or professional advice. Results depend on the inputs and on rules that vary by place and provider. Confirm important decisions with a qualified professional and the relevant documents.

2026 update

How to use the professional output

This page is not just a formula box. The result is designed to be checked, compared, and taken away.

  • Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
  • A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
  • Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.

The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.

Calccc Editorial Team · Updated 2026-11-19

Prepared by Calccc Editorial Team as an educational estimate. This page is not a licensed professional review and is not financial, medical, legal, or tax advice.

Editorial estimate prepared by the Calccc Editorial Team; not a licensed professional review.