What this calculator does
Training load is a way to put a number on how much work a week asks of you, so that a hard week and an easy week can be compared. The simplest version uses the session itself: duration in minutes multiplied by rate of perceived exertion, a 1 to 10 score for how hard the whole session felt. A 60-minute session at RPE 7 is 420 units; four of them make 1,680 units for the week. The figure is crude, because a hard set and an easy set within the same session count the same, but it is easy to record, it needs no equipment, and it tracks the training stress that athletes actually feel. The more useful number is the comparison with recent weeks. Dividing this week's load by the average of the last four weeks gives an acute:chronic ratio, a rough signal of whether training is progressing gradually or jumping faster than the body has been prepared for.
How to use it
- Record the full duration of the session, including warm-up and conditioning.
- Rate the whole session from 1 (very easy) to 10 (maximal) after it ends.
- Multiply duration by RPE for the session load, or enter both here.
- Enter the number of similar sessions in a typical week.
- Add the average weekly load from the last four weeks as the baseline.
- Compare the acute:chronic ratio with the typical range and adjust the next week.
How it works
Example calculations
Example 1: A steady four-session week
Four 60-minute sessions at RPE 7.0 produce 1,680 units against a recent average of 1,200. The ratio is 1.40, which is above the middle of the typical range and worth watching if the next week rises again. Total load for four weeks at this rate is about 7,274 units.
Example 2: Three easier sessions
Three 45-minute sessions at RPE 8.0 give 360 per session and 1,080 for the week. Against the same 1,200 baseline the ratio is 0.90, inside the typical range. A lighter week is not lost training; it is often what makes the next block possible.
Example 3: A sudden spike
Five 90-minute sessions at RPE 9.0 produce 4,050 units, more than double the default week. The ratio rises to 3.38, well above the typical range. That does not guarantee injury, but it is the pattern most coaches try to avoid, and it is a reason to hold the next week steady rather than add more.
What the result means
The weekly number is useful mainly for comparison: with yourself last month, with the same block last year, or with the plan you wrote. The ratio adds context. Values near 0.8 to 1.3 describe a week that is close to what the body has been doing; a jump above 1.5 is a rapid increase, and a ratio well below 0.8 is a sharp drop, which can be deliberate in a deload or unintentional after illness. Session RPE is subjective, and that is both its weakness and its strength: it captures heat, sleep, stress, and the actual difficulty of the work, which a stopwatch cannot. Record the score consistently, ideally at the same point after each session, and do not treat a single week's ratio as a verdict.
Common mistakes
- Counting only the main set and leaving out warm-up, conditioning, or cool-down.
- Rating effort before the session instead of after it.
- Changing the RPE scale from week to week, which breaks the comparison.
- Comparing a ratio with someone else's instead of your own baseline.
- Treating a high ratio as proof of injury risk rather than a signal to review the plan.
- Ignoring sleep, illness, and life stress that make the same load feel harder.
Assumptions and limits
- Session RPE is recorded consistently on the same 1 to 10 scale.
- The recent weekly load is a genuine four-week average in the same units.
- Duration includes the whole session, not only the hardest block.
- The sessions entered are representative of a typical week.
- The ratio is a planning heuristic, not a medical or diagnostic measure.
- Load is treated as comparable across modes, which is an approximation.
Frequently asked questions
What is session RPE?
Session RPE is the perceived effort for an entire session, usually scored 1 to 10 after the work is finished. Multiplying it by duration gives a load figure in arbitrary units. It is popular because it is simple and captures how hard the session actually felt.
What is a good acute:chronic ratio?
Values around 0.8 to 1.3 are commonly described as the typical range. The default week is 1.40, just above it, and the spike example is 3.38. These bands are planning guides, not rules, and individual tolerance varies.
Does training load predict injury?
Not reliably on its own. Load spikes are associated with higher injury rates in some studies, but sleep, previous injury, technique, and luck all matter. Use the ratio to avoid abrupt increases, not as a guarantee of safety.
How do I set my baseline?
Average the weekly load over the last four weeks, including lighter and heavier weeks. If you are returning from a break, use the weeks before the break or start with a conservative baseline and rebuild gradually.
Should strength and cardio sessions be counted the same way?
They can be, if you score RPE consistently for each. The units are arbitrary, so the comparison is most meaningful within the same activity and the same person. Combining modes is an approximation, not a precise physiological measure.
What should I do if my ratio is too high?
Hold or reduce the next week's volume or intensity, protect sleep, and check whether the spike was planned. A single high week after a long block is different from a pattern of repeated jumps; the pattern is what matters.
Sources
2026 update
How to use the professional output
This page is not just a formula box. The result is designed to be checked, compared, and taken away.
- Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
- A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
- Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.
The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.