Skip to content

FTP Calculator

Enter the average power from a test effort and choose the protocol. The calculator applies the protocol factor to estimate FTP, then shows watts per kilogram and the training zones in watts. A 250 W twenty-minute test gives an FTP of about 238 W, or 3.17 W/kg for a 75 kg rider.

Updated 2026-11-19 Editorial estimate Calccc Editorial Team Free · No sign-up
W
kg
Scenarios A/BSave two input sets and compare the results. Stored only in this browser.
AEmpty
BEmpty

Your inputs stay in this browser. No account, no uploads.

Professional worksheet

Detailed schedule & assumptions

Inputs used, method, sensitivity, and any year-by-year table. The summary above stays compact; the audit lives here.

Professional worksheet

Inputs, scope, and sensitivity

Inputs used

Method and scope

Result audit

MetricValue

What this calculator does

Functional threshold power is the highest power a rider can hold for about an hour without fading, and it is the anchor for most power-based training. Because a full hour test is hard to pace and repeat, most riders estimate FTP from a shorter effort and apply a protocol factor: 95% of a 20-minute test, 90% of an 8-minute test, or the average of a 60-minute effort directly. The estimate is only as good as the test, and pacing, fatigue, temperature, and equipment all move the number. This calculator applies the standard factors, converts the result to watts per kilogram, and builds six training zones from the estimate. Use it to set zones for a block of training, then retest after a few weeks and adjust rather than treating one test as a permanent label.

How to use it

  1. Warm up thoroughly before the test effort, including a few hard minutes.
  2. Ride the test distance or duration as evenly as possible.
  3. Enter the average power from the test, not the normalized power.
  4. Choose the protocol that matches the test you actually rode.
  5. Enter body weight to get watts per kilogram.
  6. Use the zone ranges for training and retest every four to eight weeks.

How it works

FTP = test average power × protocol factor, where the factor is 0.95 for a 20-minute test, 0.90 for an 8-minute test, and 1.00 for a 60-minute effort. Watts per kilogram = FTP / body weight. Zones are percentages of FTP: endurance 56–75%, tempo 76–90%, threshold 91–105%, VO2 max 106–120%. In the default case: 250 W × 0.95 = 237.5 W; 237.5 / 75 = 3.17 W/kg.

Example calculations

Example 1: A 20-minute test

A 75 kg rider averages 250 W for 20 minutes. Applying 95% gives an estimated FTP of 237.5 W, or 3.17 W/kg. The threshold zone runs from about 216 W to 249 W, and the endurance zone from about 133 W to 178 W. The rider should be able to repeat threshold intervals in that band without blowing up.

Example 2: An 8-minute test

A lighter rider averages 300 W for 8 minutes and weighs 60 kg. The 90% factor gives an FTP of 270 W, or 4.50 W/kg. Short tests are easier to pace but are more sensitive to anaerobic capacity, so the estimate can be optimistic for riders with a strong short-duration punch.

Example 3: A 60-minute effort

A rider completes a 40 km time trial in about an hour at 260 W average and weighs 80 kg. With a factor of 1.00 the FTP estimate is 260 W, or 3.25 W/kg. A full-hour effort avoids the protocol correction, but it is demanding and only useful when the course and conditions allow a steady effort.

What the result means

FTP is a training anchor, not a fixed physiological threshold. It moves with fitness, fatigue, altitude, heat, and even the time of day, and different tests give different estimates for the same rider. The zones are guidelines: endurance work should feel conversational, tempo should be comfortably hard, threshold should be sustainable for about an hour in total, and VO2 max work should be hard enough that repetitions become difficult after a few minutes. A single test can be off by several percent, so confirm the estimate by checking whether threshold intervals are repeatable at the prescribed watts. If they are not, adjust the number rather than forcing the workout.

Common mistakes

  • Using normalized power from a variable ride instead of a steady test average.
  • Skipping the warm-up and starting the test effort cold.
  • Applying the 20-minute factor to a 20-minute segment inside a longer ride without pacing it.
  • Retesting in a different position or on different equipment.
  • Treating the estimate as a fixed number and never updating it.
  • Ignoring body weight changes when comparing watts per kilogram.

Assumptions and limits

  • The test effort was paced as evenly as possible.
  • The power meter is calibrated and reads consistently with previous tests.
  • The protocol factor matches the test actually performed.
  • Body weight is measured on the test day.
  • Training zones are percentages of FTP and are not individually validated.
  • Heat, altitude, and fatigue were similar to normal training conditions.

Frequently asked questions

What is FTP?

Functional threshold power is the highest average power a rider can sustain for roughly an hour. It is used as the reference for training zones because it sits near the boundary between sustainable and unsustainable efforts.

Why use 95% of a 20-minute test?

A 20-minute effort is ridden slightly above true hour power for most riders, so the 95% factor is an empirical correction. It is widely used because a 20-minute test is repeatable and much less demanding than a full hour.

Which test protocol is best?

The 20-minute test is the most common compromise. The 8-minute test is shorter but more influenced by anaerobic capacity, and the 60-minute effort is the most direct but hardest to pace and recover from. Consistency matters more than the choice.

How often should I retest?

Every four to eight weeks during a structured training block, or after a significant break. Retest in similar conditions and with the same equipment so that changes reflect fitness rather than setup.

Is FTP the same as lactate threshold?

They are related but not identical. FTP is a power-based field estimate, while lactate threshold is a physiological measurement. For most training purposes the two are close enough that FTP is used as a practical stand-in.

What should my watts per kilogram be?

There is no universal target. Values depend on riding type, body size, and training history. Track your own trend over time and compare within similar riders rather than against elite figures.

Sources

This calculator is an educational planning tool, not financial, legal, insurance, medical, or professional advice. Results depend on the inputs and on rules that vary by place and provider. Confirm important decisions with a qualified professional and the relevant documents.

2026 update

How to use the professional output

This page is not just a formula box. The result is designed to be checked, compared, and taken away.

  • Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
  • A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
  • Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.

The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.

Calccc Editorial Team · Updated 2026-11-19

Prepared by Calccc Editorial Team as an educational estimate. This page is not a licensed professional review and is not financial, medical, legal, or tax advice.

Editorial estimate prepared by the Calccc Editorial Team; not a licensed professional review.