The short answer: total rise is the floor-to-floor height. Divide by a comfortable riser height (usually 7–7.75 in) to get the number of risers, then round to a whole number and divide again for the exact riser. Run = tread depth × number of treads. Check local code for maximum rise and minimum tread.

Key takeaways

  • Total rise is floor to floor.
  • Riser height and tread depth are regulated.
  • The number of treads is one less than the number of risers.
  • Stringer length uses the Pythagorean theorem.
  • Check code and headroom before cutting.

The math

Total rise 108 in. Try a 7.5 in riser: 108 ÷ 7.5 = 14.4, so 14 or 15 risers. 108 ÷ 14 = 7.714 in; 108 ÷ 15 = 7.2 in. Both are within a typical 7–7.75 in range; choose the one that fits the run. Treads = risers − 1. A 10.5 in tread with 14 risers gives 13 treads × 10.5 = 136.5 in run.

Code limits

Residential code often limits riser height to 7.75 in and tread depth to at least 10 in, with variations. Commercial stairs are stricter. Handrails, guards, landings, and headroom also have requirements. The calculator gives the geometry, not the code approval.

Stringer length

Stringer length = √(rise² + run²). For a 108 in rise and 136.5 in run, the stringer is about 174 in, or 14.5 ft. Add for the top and bottom cuts. Use a framing square or a calculator to mark the steps consistently.

Landings and headroom

A long stair may need a landing. Headroom is measured vertically from the tread nosing to the ceiling or obstruction; code requires a minimum. A stair that fits the math can still fail the headroom check.

What to compare

Compare the riser height, tread depth, run, stringer length, and headroom. A comfortable stair has consistent risers; a single short or tall step is a trip hazard.

A 108 in example

Total rise 108 in. 14 risers give 7.714 in each; 15 risers give 7.2 in. With 14 risers, 13 treads × 10.5 in = 136.5 in run. Stringer = √(108² + 136.5²) = 174 in, or 14.5 ft. Add for the top and bottom cuts.

Comfort and code

A consistent riser is more important than a perfect number. A 7.5 in riser and 10.5 in tread is comfortable for many adults. Check the local code for maximum rise, minimum tread, handrail, and headroom.

What to compare

Compare the riser, tread, run, stringer, and headroom. A stair that fits the math can still fail the code.

Layout and cuts

Mark the stringer with a framing square using the rise and run. Check the first and last cuts before cutting all the stringers. A stair with inconsistent risers is a trip hazard. Test-fit the first tread and riser before installing the rest.

Handrails and guards

Stairs above a certain height need a handrail and guards. The height and spacing are regulated. A stair that meets the rise/run code can still fail the handrail requirement.

What to compare

Compare the riser, tread, run, stringer, headroom, and handrail requirements.

Materials

Stringers are usually 2×12 lumber; treads and risers are separate. A stair with a closed riser uses more material. The handrail and balusters are measured in linear feet and count, not board feet.

What to compare

Compare the stringer length, tread count, riser count, handrail, and code requirements. A stair that is cheap to build but uncomfortable is not a good trade.

A second example

Total rise 96 in. 13 risers give 7.38 in; 14 risers give 6.86 in. With 13 risers, 12 treads × 10.5 = 126 in run. Stringer = √(96² + 126²) = 158 in, or 13.2 ft. Check headroom and code.

What to compare

Compare the riser, tread, run, stringer, and code requirements.

What to compare

Compare the riser, tread, run, stringer, headroom, and handrail requirements. A stair that fits the math can still fail the local code.

Test-fit the first tread and riser before cutting all the stringers.

Code and safety

A stair with inconsistent risers is a trip hazard. Handrails, guards, and headroom are regulated. A stair that fits the rise/run math can still fail the local code. Check before cutting; moving a stair is expensive.

What to compare

Compare the riser, tread, run, stringer, headroom, and handrail requirements.

Stringer layout

Mark the rise and run on the stringer with a framing square, then check the first and last cuts before cutting all the stringers. Test-fit the first tread and riser. A consistent riser is more important than a perfect number.

What to compare

Compare the riser, tread, run, stringer, headroom, and handrail requirements.

Handrail height

Handrails are usually 34–38 in above the tread nosing, with a graspable profile. Guards are required above a certain height. The spacing of balusters is regulated to prevent a child from passing through. Check the local code before installing.

What to compare

Compare the handrail, guard, baluster count, and stair geometry.

Check the handrail and guard rules before installing the stair.

Test-fit the first tread.

Compare the handrail and guard rules with the stair plan before cutting the stringers and installing the treads.

Compare the handrail and guard requirements with the local code before cutting the stringers and installing the treads.

Check the code before cutting the stringers and installing the treads.

Check the local code before cutting the stringers and installing the treads.

Frequently asked questions

How do I calculate stair rise and run?

Divide the total rise by the desired riser height, round to a whole number, then divide again. Run = tread depth × (risers − 1).

What is a comfortable riser height?

Usually 7–7.75 in for residential stairs, subject to code.

How long is the stringer?

√(rise² + run²), plus allowances for cuts.

Do I need a landing?

It depends on the total rise and code. Check the local requirements.

Further reading

Keep exploring

Read next Roofing: Squares, Pitch, Waste, and Cost Convert a roof footprint into sloped area, squares, and bundles with the pitch multiplier. Includes waste allowances, a… Read next MPG: Real-World Fuel Economy and Cost per Mile MPG is miles divided by gallons, and cost per mile is price divided by MPG. Learn to measure… Read next Party Planning: Guests, Food, Drink, and Budget Estimate food, drink, and cost per guest with a simple multiplication model, then adjust for buffet portions, ice,…