The short answer: deck boards are estimated by area ÷ board coverage, plus 10–15% waste. Joists are spaced 12–16 in on center, and the count depends on the deck width. Footings support the posts and beams; the size depends on the load and soil.

Key takeaways

  • Board coverage depends on width and gap.
  • Joist spacing and span depend on the decking and load.
  • Footings need size and depth for frost.
  • Add waste for cuts and board ends.
  • Check local code before building.

Decking boards

A 5.5 in board with a 0.25 in gap covers 5.75 in of deck width. For a 12 ft wide deck, 144 ÷ 5.75 = 25.04, so 26 boards across. For a 16 ft length, boards are usually 16 ft or 12 ft; the number of rows depends on the board length and the layout. Add 10–15% waste.

Joists

Joists are spaced 12, 16, or 24 in on center, depending on the decking and load. For a 12 ft wide deck at 16 in on center: 144 ÷ 16 = 9 spaces, so 10 joists, plus rim joists. The joist span must be checked against the species, size, and load; do not guess.

Footings

Footings support posts and beams. A common footing is 12 in diameter and 36–48 in deep, below frost line. The required size depends on the tributary load and soil. A deck close to the ground may use a different foundation. Check local code and have the plans reviewed.

Waste and layout

Deck boards may need 10–15% waste for cuts, angled ends, and defects. A diagonal layout needs more. Keep a few extra boards for future repairs. A picture-frame border changes the layout and the waste.

What to compare

Compare the board count, joist count, footing size, and hardware. A cheap decking with a short span may require more joists; the total cost can be higher.

A 12×16 example

Deck 12 ft × 16 ft = 192 sq ft. 5.5 in boards with 0.25 in gap cover 5.75 in: 144 ÷ 5.75 = 25.04, so 26 rows. If boards run 16 ft, 26 boards; add 10% = 29. Joists at 16 in on center: 144 ÷ 16 = 9 spaces, 10 joists, plus rim joists. Footings depend on the beam layout.

Footing size

A 12 in diameter, 36 in deep footing has about 2.36 cu ft, or 0.087 cu yd. An 80 lb bag yields about 0.6 cu ft, so 4 bags. Check the local frost depth and load.

What to compare

Compare the board count, joist count, footing size, and hardware. A short-span decking may need more joists.

Code and guards

Decks above a certain height need guards and handrails. Stairs need footings and stringers. Joist spans depend on species and load. A deck that is not permitted can create liability and resale problems. Check the local code before building.

Fasteners

Use galvanized or stainless fasteners compatible with the decking. Hidden fasteners change the board gap and the layout. Add the fastener cost to the budget.

What to compare

Compare the board count, joist count, footing size, hardware, and permit requirements.

Board layout

Run boards parallel to the house or perpendicular, depending on the look and the joists. A picture-frame border changes the count. Leave a gap for drainage and expansion; the gap size depends on the material and moisture.

What to compare

Compare the board count, joist count, footing, hardware, and permit. A low board price can be offset by more joists or a stronger frame.

A second deck example

A 10×12 deck is 120 sq ft. 5.5 in boards with 0.25 in gap: 120 ÷ 5.75 = 20.9, so 21 rows. At 12 ft lengths, 21 boards; add 10% = 24. Joists at 16 in on center: 120 ÷ 16 = 7.5, so 9 joists, plus rims. Footings depend on the beam.

What to compare

Compare the board count, joist count, footing, and hardware.

What to compare

Compare the board count, joist count, footing size, hardware, and permit requirements. A short-span decking may require more joists, which can offset a lower board price.

Check the guard and stair requirements before building.

Stairs and guards

A deck stair needs stringers, footings, and a handrail. Guards are required above a certain height. The joist span and footing size depend on the load and soil. A deck that is not permitted can create liability and resale problems.

What to compare

Compare the board count, joist count, footing, hardware, and permit requirements.

Board gap and drainage

Leave a gap between deck boards for drainage and expansion. The gap size depends on the material and moisture. A hidden fastener system changes the gap and the layout. Keep the deck surface slightly sloped away from the house.

What to compare

Compare the board count, joist count, footing, hardware, and permit.

Footing depth

Footings must be below the frost line in cold climates. A shallow footing can heave and crack the deck. Check the local frost depth and the required footing size. A deck attached to the house needs proper ledger flashing and lagging.

What to compare

Compare the footing depth, board count, joist count, and hardware.

Check the frost depth before ordering the footings and concrete.

Compare the frost depth with the footing plan before ordering concrete.

Compare the footing depth with the local frost line before ordering.

Frequently asked questions

How many boards do I need for a deck?

Divide the deck width by the board coverage (width plus gap), then multiply by the number of rows and add waste.

How far apart are deck joists?

Usually 12–16 in on center, depending on the decking and load. Check the span table.

How deep should footings be?

Below the local frost line, often 36–48 in in cold climates. Check code.

Do I need a permit?

Most jurisdictions require a deck permit. Check before building.

Further reading

Keep exploring

Read next Roofing: Squares, Pitch, Waste, and Cost Convert a roof footprint into sloped area, squares, and bundles with the pitch multiplier. Includes waste allowances, a… Read next MPG: Real-World Fuel Economy and Cost per Mile MPG is miles divided by gallons, and cost per mile is price divided by MPG. Learn to measure… Read next Party Planning: Guests, Food, Drink, and Budget Estimate food, drink, and cost per guest with a simple multiplication model, then adjust for buffet portions, ice,…