Skip to content

Concrete Mix Calculator

Enter the wet concrete volume, choose a cement : sand : gravel ratio, and set the water–cement ratio. The calculator estimates cement in kilograms, sand and gravel in cubic metres, and water in litres using a dry-volume factor of 1.54 and a cement bulk density of 1,440 kg/m³. It is a batching estimate, not a designed mix.

Updated 2026-11-18 Editorial estimate Calccc Editorial Team Free · No sign-up
m³

0.45–0.55 suits most general concrete. A lower ratio is stronger but harder to place.

%
Advanced options
kg/m³

Converts wet volume to dry material volume; 1.54 is a common allowance for voids and bulking.

Scenarios A/BSave two input sets and compare the results. Stored only in this browser.
AEmpty
BEmpty

Your inputs stay in this browser. No account, no uploads.

Professional worksheet

Detailed schedule & assumptions

Inputs used, method, sensitivity, and any year-by-year table. The summary above stays compact; the audit lives here.

Professional worksheet

Inputs, scope, and sensitivity

Inputs used

Advanced inputs used

Method and scope

Result audit

MetricValue

What this calculator does

A nominal mix ratio is a recipe by volume, not a guarantee of strength. The ratio tells you how many parts of cement, sand, and gravel to combine, but the water, the aggregate grading, and the way the materials are measured decide what the concrete actually does. This calculator uses the common dry-volume method: the wet volume is multiplied by 1.54 to allow for voids and bulking, the dry volume is split by the mix parts, and cement is converted to kilograms using a bulk density of 1,440 kg/m³. That gives a practical shopping list for bags, sand, and gravel. It is not a substitute for a designed mix with tested materials, and it cannot tell you whether 1:2:3 is strong enough for a structural element.

How to use it

  1. Enter the wet concrete volume you need to place, in cubic metres.
  2. Choose a nominal mix ratio, or keep 1:2:3 for general-purpose work.
  3. Set the water–cement ratio. 0.45–0.55 is typical for general concrete.
  4. Add a waste allowance for spillage and over-excavation.
  5. Read the cement, sand, gravel, water, and 50 kg bag count.

How it works

Wet volume = entered volume × (1 + waste ÷ 100). Dry volume = wet volume × 1.54. Cement (kg) = dry volume × (cement parts ÷ total parts) × 1,440. Sand (m³) = dry volume × (sand parts ÷ total parts). Gravel (m³) = dry volume × (gravel parts ÷ total parts). Water (L) = cement kg × water–cement ratio. Example: 1 m³ of 1:2:3 at w/c 0.5 with 5% waste gives 1.05 m³ wet, 1.617 m³ dry, 388 kg cement, 0.54 m³ sand, 0.81 m³ gravel, and 194 L water.

Example calculations

Example 1: 1 m³ of 1:2:3 at w/c 0.5, 5% waste

Wet volume = 1.05 m³ and dry volume = 1.617 m³. Cement = 1.617 ÷ 6 × 1,440 = 388 kg. Sand = 1.617 × 2 ÷ 6 = 0.54 m³. Gravel = 1.617 × 3 ÷ 6 = 0.81 m³. Water = 388 × 0.5 = 194 L. That is about 8 bags of 50 kg cement.

Example 2: 0.5 m³ of 1:2:3 at w/c 0.5, 5% waste

Halving the volume halves every material: 194 kg cement, 0.27 m³ sand, 0.40 m³ gravel, and 97 L water. Small pours are sensitive to measuring error, so weigh the cement and use a marked bucket for the water.

Example 3: 2 m³ of 1:1.5:3 at w/c 0.45, 5% waste

Wet volume = 2.1 m³ and dry volume = 3.234 m³. Total parts = 5.5, so cement = 3.234 ÷ 5.5 × 1,440 = 847 kg. Sand = 0.88 m³, gravel = 1.76 m³, and water = 381 L. The richer mix uses more cement per cubic metre than 1:2:3.

What the result means

The dry-volume factor of 1.54 is the biggest assumption in the result. It accounts for the voids between aggregate particles and the bulking of damp sand, and it is the reason the dry volume is larger than the wet volume you place. Real factors vary with aggregate shape, moisture, and how the materials are measured, so treat the output as a batching target and adjust on the first mix. The water–cement ratio is the second big lever: lowering it increases strength and durability but makes the mix stiffer, while adding water for workability weakens the hardened concrete. Nominal mixes such as 1:2:3 are acceptable for non-structural work in many jurisdictions, but structural concrete should be specified by strength and tested, not by a volume ratio. If the project needs a particular strength class, get a designed mix.

Common mistakes

  • Treating a nominal 1:2:3 ratio as a guaranteed strength specification.
  • Adding water on site to improve workability without adjusting the cement.
  • Measuring sand and gravel by loose shovels instead of a consistent volume.
  • Forgetting that damp sand bulks and changes the actual volume.
  • Mixing only the exact calculated volume with no allowance for spillage and waste.

Assumptions and limits

  • The mix ratio is by volume of dry materials, not by weight.
  • The dry-volume factor is 1.54, a common allowance for voids and bulking.
  • Cement bulk density is 1,440 kg/m³ and water weighs 1 kg per litre.
  • Sand and gravel volumes are loose (bulked) volumes as delivered.
  • Aggregates are clean, well graded, and used at their stated moisture content.

Frequently asked questions

What does a 1:2:3 mix mean?

One part cement, two parts sand, and three parts gravel by volume. It is a common general-purpose nominal mix for paths, pads, and non-structural work. It is not a strength class, and the actual strength depends on the water ratio and the materials.

How much water should I add?

Start from the water–cement ratio: 0.5 means 0.5 kg (or 0.5 L) of water per kilogram of cement. Add most of it, mix, and then adjust carefully for workability. Water demand also depends on aggregate moisture, so the first mix is always a calibration.

Why is the dry volume larger than the wet volume?

Dry sand and gravel contain voids between particles. When water and cement fill those voids, the combined wet volume is smaller than the sum of the dry ingredients. The 1.54 factor expands the wet volume back to the dry material volume needed to batch it.

How many 50 kg bags of cement are in 1 m³?

For 1:2:3 at a water–cement ratio of 0.5 with 5% waste, about 388 kg, or roughly 8 bags of 50 kg. A richer mix such as 1:1.5:3 uses more cement, and a leaner mix uses less.

Can I use this mix for a foundation or slab?

Only if the project's specification allows a nominal mix. Structural foundations, suspended slabs, and reinforced elements usually require a designed mix with a specified strength and tested materials. Check the drawing or ask an engineer.

How do I convert sand and gravel from cubic metres to kilograms?

Multiply the volume by the material's bulk density: about 1,600 kg/m³ for dry sand and 1,500–1,700 kg/m³ for gravel, depending on grading and moisture. Suppliers usually sell by volume or by the tonne, so ask which measure their price uses.

Sources

This calculator is an educational batching estimate. It is not a designed mix, a strength specification, or a structural recommendation. Concrete performance depends on materials, grading, water content, curing, and testing; specify structural concrete by strength with a qualified engineer or supplier.

2026 update

How to use the professional output

This page is not just a formula box. The result is designed to be checked, compared, and taken away.

  • Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
  • A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
  • Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.

The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.

Calccc Editorial Team · Updated 2026-11-18

Prepared by Calccc Editorial Team as an educational estimate. This page is not a licensed professional review and is not financial, medical, legal, or tax advice.

Editorial estimate prepared by the Calccc Editorial Team; not a licensed professional review.