Skip to content

Fence Picket Calculator

Enter the fence run, the picket width, and the gap you want between pickets. The calculator returns the number of pickets to buy, including waste, the pitch, the pickets per metre, and the length of run the count actually covers.

Updated 2026-11-18 Editorial estimate Calccc Editorial Team Free · No sign-up
m
mm
mm

Check local rules: many areas limit gaps for pool and boundary fencing.

%
Scenarios A/BSave two input sets and compare the results. Stored only in this browser.
AEmpty
BEmpty

Your inputs stay in this browser. No account, no uploads.

Professional worksheet

Detailed schedule & assumptions

Inputs used, method, sensitivity, and any year-by-year table. The summary above stays compact; the audit lives here.

Professional worksheet

Inputs, scope, and sensitivity

Inputs used

Method and scope

Result audit

MetricValue

What this calculator does

A picket fence looks simple until the spacing has to come out even. The number of pickets is set by the run, the picket width, and the gap, and small changes in any of them shift the count. Getting it wrong is expensive in both directions: too few means a second order and a colour match problem, too many means wasted timber. The arithmetic is straightforward once the pitch, the distance from the start of one picket to the start of the next, is known. Dividing the run by the pitch gives the count, and the remaining length tells you whether the final gap will be tight or wide. This calculator does that, rounds up so both ends finish with a picket, and adds a waste allowance for offcuts and defects.

How to use it

  1. Measure the straight run between the end posts.
  2. Enter the actual face width of the picket, not the nominal size.
  3. Choose a gap and check local rules for boundary and pool fencing.
  4. Add a waste allowance for cutting and defects.
  5. Check the covered length before ordering to confirm the spacing works.

How it works

Pitch = picket width + gap. Pickets = ceil((run + gap) / pitch). Pickets to buy = ceil(pickets x (1 + waste)). In the default case, (24,000 mm + 20 mm) / 120 mm = 201 pickets, and with 5% waste you buy 212.

Example calculations

Example 1: 24 m of fence with 100 mm pickets and 20 mm gaps

The pitch is 120 mm, so the run needs 201 pickets. With 5% waste the order is 212. The count covers 24.10 m, slightly more than the run, which is why the last gap closes cleanly.

Example 2: 40 m with wider pickets and gaps

A 145 mm pitch on a 40 m run needs 277 pickets, or 305 with 10% waste. Wider pickets reduce the count but raise the weight per metre of fence.

Example 3: A short privacy run with tight gaps

A 12 m run with 90 mm pickets and 10 mm gaps gives a 100 mm pitch and 121 pickets, or 128 after waste. Tight gaps look neat but trap wind, so check the rail and post specification.

What the result means

The count is only as good as the run measurement. Measure between post faces rather than centre to centre, because the pickets span the clear distance, and measure at the height of the rails in case the ground slopes. If the run is stepped, treat each horizontal section as a separate run and add a little extra for the step ends. Gap width is a design and sometimes a legal choice: a 100 mm opening is a common safety threshold for barriers, and pool fencing rules are usually stricter. Wind load also rises as gaps close, so a tight picket fence needs more robust posts and rails than the picket count alone suggests.

Common mistakes

  • Using nominal picket size instead of the actual face width.
  • Measuring post centres instead of the clear run between posts.
  • Forgetting the extra picket that closes the far end of the run.
  • Ignoring gates, which break the run and add waste.
  • Choosing a gap that does not match the local fencing rules.
  • Ordering exactly the count with no allowance for defects.

Assumptions and limits

  • The run is straight and level between two end posts.
  • Every picket has the same face width.
  • Gaps are uniform along the run.
  • Both ends of the run finish with a full picket.
  • Waste covers cutting and minor defects, not a design change.

Frequently asked questions

How many pickets do I need per metre?

Divide 1,000 mm by the pitch. With 100 mm pickets and a 20 mm gap the pitch is 120 mm, so there are about 8.3 pickets per metre.

Why add a gap to the run in the formula?

It ensures the run starts and ends with a full picket rather than a half gap. Without it the last picket can sit past the end of the run or leave an uneven gap.

What gap should I use?

Twenty millimetres is a common balance between privacy and wind passage. Check local rules for pool barriers and boundary fences, since some set a maximum opening.

How do I handle a sloped run?

Build in level sections and step the fence at posts, or rake the pickets. Each section needs its own count, and stepped ends add a little waste.

Does this include rails and posts?

No. Use the fence calculator for posts, panels, and concrete, and this tool for the picket count itself.

How much waste should I allow?

Five percent is enough for a straight run with clean timber. Use ten percent or more for short runs, brittle species, or many cuts.

Sources

This calculator counts pickets only. It does not check structural requirements, wind loading, or local fence regulations, and it does not include posts, rails, or fixings. Confirm rules with the local authority before building.

2026 update

How to use the professional output

This page is not just a formula box. The result is designed to be checked, compared, and taken away.

  • Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
  • A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
  • Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.

The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.

Calccc Editorial Team · Updated 2026-11-18

Prepared by Calccc Editorial Team as an educational estimate. This page is not a licensed professional review and is not financial, medical, legal, or tax advice.

Editorial estimate prepared by the Calccc Editorial Team; not a licensed professional review.