Skip to content

Irrigation Calculator

Enter the area, the depth of water the planting needs each week, and the flow rate of your tap or pump. The calculator converts the depth into litres, adjusts for application efficiency, and divides by the flow to give the run time per week and per session. For 100 m² at 25 mm a week and 15 L/min, each of 3 sessions runs about 65 minutes.

Updated 2026-11-19 Editorial estimate Calccc Editorial Team Free · No sign-up
m²
mm

The depth of water the planting needs each week, not the runtime.

L/min

Measured flow from the tap, hose, or pump feeding the zone.

%

Sprinklers lose water to wind and evaporation; drip lines are usually higher.

Advanced options
wks
Scenarios A/BSave two input sets and compare the results. Stored only in this browser.
AEmpty
BEmpty

Your inputs stay in this browser. No account, no uploads.

Professional worksheet

Detailed schedule & assumptions

Inputs used, method, sensitivity, and any year-by-year table. The summary above stays compact; the audit lives here.

Professional worksheet

Inputs, scope, and sensitivity

Inputs used

Advanced inputs used

Method and scope

Result audit

MetricValue

What this calculator does

Watering advice is usually given as a depth, such as 25 mm a week, but a tap is measured in litres per minute and a controller in minutes. The conversion is simpler than it looks: one millimetre of water over one square metre is one litre, so the weekly volume is the area multiplied by the depth in millimetres. What makes it practical is efficiency. Sprinklers lose water to wind, evaporation, and runoff before it reaches the roots, so the delivered depth has to be divided by an efficiency figure to get the water that must actually leave the tap. Run time then follows from the flow rate and the number of sessions. The result is a starting schedule, not a guarantee. Soil type, slope, and plant roots decide how much of the water stays where it is needed, and watering in two shorter cycles is often better than one long one on soil that cannot absorb the flow.

How to use it

  1. Measure the area the sprinkler or drip zone actually covers.
  2. Enter the weekly water depth the plants need, not the run time.
  3. Measure the flow at the tap or pump with a bucket and a timer.
  4. Set an efficiency that matches the method: drip is higher than sprinklers.
  5. Choose how many sessions per week you can water.
  6. Use the per-session run time and check the soil at root depth afterwards.

How it works

Weekly litres = area × depth in mm; delivered litres = weekly litres ÷ efficiency; run time per week = delivered litres ÷ flow in litres per minute; run time per session = weekly run time ÷ sessions. The default 100 m² × 25 mm needs 2,500 L, or 2,941 L after efficiency, which takes 196 minutes a week.

Example calculations

Example 1: 100 m² at 25 mm a week

The weekly requirement is 2,500 L. At 85% efficiency that becomes 2,941 L, and at 15 L/min the run time is 196 minutes a week. Split over 3 sessions, that is 65 minutes each, applying about 9.0 mm per hour.

Example 2: 200 m² at 30 mm with a stronger flow

Doubling the area and raising the depth to 30 mm needs 6,667 L a week. A 20 L/min flow and 90% efficiency bring the run time to 167 minutes per session over 2 sessions. The application rate is only 6.0 mm/h, so longer runs risk runoff on heavy soil.

Example 3: A 50 m² drip zone

Drip lines are efficient, so 95% is realistic. The zone needs 789 L a week, and at 8 L/min each of 3 sessions runs about 33 minutes. The same area under a sprinkler would need longer, because more water is lost before it reaches the roots.

What the result means

Run time is the output people want, but the input that matters is the depth. Two gardens with the same area can need very different amounts of water because one is in full sun and the other is shaded, or because one has established shrubs and the other has new seedlings. The efficiency figure is where most schedules go wrong: a sprinkler rated at 15 L/min does not deliver 15 litres to the root zone every minute, and wind can waste a third of it. Application rate is the other check. If the calculated rate is much above the soil's infiltration rate, water will run off, and the answer is to split the run into cycles rather than to water longer. Seasonal totals show why a schedule is worth setting: the default season uses 88.2 m³, which is a real cost on a meter.

Common mistakes

  • Watering by minutes without checking the depth delivered.
  • Using the sprinkler's rated flow instead of the measured flow.
  • Assuming 100% efficiency for a sprinkler in wind.
  • Applying the whole weekly depth in one run on soil that cannot absorb it.
  • Ignoring the area covered by the zone and watering the whole garden instead.
  • Forgetting that established plants need less water than new plantings.

Assumptions and limits

  • The stated depth is the net amount the plants need at the root zone.
  • The flow rate is measured at the point where the system connects.
  • Application is uniform across the area.
  • Efficiency accounts for wind, evaporation, and runoff losses.
  • The number of sessions divides the weekly volume evenly.
  • Rainfall is not credited; reduce the schedule when rain does the work.

Frequently asked questions

How long should I water my garden?

It depends on the area, the flow, and the depth needed. For 100 m² at 25 mm a week with a 15 L/min flow, the calculator gives about 65 minutes per session over 3 sessions.

How much water is 25 mm a week?

Twenty-five millimetres over one square metre is 25 litres. Over 100 m² it is 2,500 litres a week before efficiency losses, which is why a meter and a schedule are worth checking.

Is drip irrigation better than sprinklers?

Drip uses less water for the same planting because it delivers to the root zone with less evaporation and wind loss. It is also easier to run without runoff. Sprinklers cover a lawn more evenly and cost less to install over a large area.

How do I measure my flow rate?

Fill a bucket of known volume from the tap or hose and time it. Divide the volume by the minutes to get litres per minute. Repeat at the actual tap or zone because pressure drops along the hose.

Should I water every day or deeply twice a week?

Deep, less frequent watering encourages roots to go deeper and is usually better for established plants. Sandy soil may need more frequent cycles, and new plantings need consistent moisture until they establish.

Does the seasonal figure include rain?

No. It is the water the system must deliver. Subtract effective rainfall or switch the controller off after meaningful rain, and check the soil rather than following the calendar.

Sources

This is an educational watering estimate, not horticultural or irrigation-design advice. Plant needs, soil, climate, and local water restrictions vary. Check the soil at root depth and follow any local watering rules.

2026 update

How to use the professional output

This page is not just a formula box. The result is designed to be checked, compared, and taken away.

  • Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
  • A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
  • Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.

The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.

Calccc Editorial Team · Updated 2026-11-19

Prepared by Calccc Editorial Team as an educational estimate. This page is not a licensed professional review and is not financial, medical, legal, or tax advice.

Editorial estimate prepared by the Calccc Editorial Team; not a licensed professional review.