Skip to content

Lumber Weight Calculator

Enter the length, width, thickness, number of pieces, and wood density. The calculator multiplies the volume of each piece by the density and the quantity. Ten pieces of 100 × 50 mm timber, 2.4 m long at 500 kg/m³, weigh 60.0 kg in total.

Updated 2026-11-19 Editorial estimate Calccc Editorial Team Free · No sign-up
m
mm
mm
kg/m³

Air-dry density. Softwoods are often 350–550 kg/m³; hardwoods 600–900 kg/m³.

Scenarios A/BSave two input sets and compare the results. Stored only in this browser.
AEmpty
BEmpty

Your inputs stay in this browser. No account, no uploads.

Professional worksheet

Detailed schedule & assumptions

Inputs used, method, sensitivity, and any year-by-year table. The summary above stays compact; the audit lives here.

Professional worksheet

Inputs, scope, and sensitivity

Inputs used

Method and scope

Result audit

MetricValue

What this calculator does

Lumber is sold by volume, but it is moved by weight. A trailer, a roof rack, a lift, or a two-person carry all have limits that are easier to exceed than they look, especially with dense hardwood or timber that has taken on water. This calculator converts a piece count and a cross-section into total weight using the volume of each piece and the density of the species. It reports the weight per piece and per metre as well, so you can check a carry or a saw horse before the whole order is loaded. The density is the input that matters most: the same 100 × 50 mm section weighs roughly half as much in a light softwood as in a dense hardwood. Use a published density for the species and moisture condition you are buying, and treat the result as an estimate rather than a weighbridge ticket.

How to use it

  1. Measure the actual finished dimensions, not the nominal size, if the timber is planed.
  2. Enter the length of one piece in metres.
  3. Enter the cross-section in millimetres.
  4. Count the pieces, including any spares or offcuts you are transporting.
  5. Enter the air-dry density for the species; use a higher figure for green or wet timber.
  6. Compare the total with the vehicle, trailer, or lift capacity before loading.

How it works

Volume per piece = (width ÷ 1000) × (thickness ÷ 1000) × length. Weight = volume × density × quantity. Weight per metre = (width ÷ 1000) × (thickness ÷ 1000) × density. In the default case, 10 pieces at 0.012 m³ each and 500 kg/m³ weigh 60.0 kg.

Example calculations

Example 1: Ten pieces of 100 × 50 mm, 2.4 m long

Each piece has a volume of 0.012 m³ and weighs 6.00 kg at 500 kg/m³. Ten pieces weigh 60.0 kg, or 0.060 tonnes. The weight per metre is 2.50 kg/m.

Example 2: Twenty longer 150 × 50 mm pieces

A larger order of 20 pieces, 3.6 m long and 150 mm wide at 600 kg/m³, has a total volume of 0.54 m³ and weighs 324.0 kg. The weight per piece is 16.2 kg, which is already a two-person lift.

Example 3: A dense hardwood

Five pieces of 200 × 50 mm, 2.4 m long at 700 kg/m³ weigh 84.0 kg despite the small piece count. Dense species can be twice the weight of softwood for the same volume, so never estimate a hardwood order from a softwood rule of thumb.

What the result means

The total weight is the number for transport; the weight per piece is the number for manual handling; the weight per metre is useful for estimating a run of timber before the cut list is final. Density is the biggest source of error. Published tables often give a range for a species, and the actual figure depends on moisture content: green timber can weigh 50% or more above its air-dry weight. If the load is close to a vehicle or lift limit, weigh a sample or use the supplier's shipping weight rather than relying on a table. The calculator assumes rectangular pieces and uniform density; it does not account for bark, wane, or metal fixings.

Common mistakes

  • Using nominal dimensions for planed timber and overstating the volume.
  • Using a softwood density for a dense hardwood species.
  • Forgetting that green or wet timber is much heavier than air-dry timber.
  • Estimating the whole order from the weight of one piece without checking density.
  • Loading a trailer or roof rack close to its limit without a margin for straps and tools.
  • Ignoring the weight of packaging, pallets, and offcuts.

Assumptions and limits

  • Each piece is a rectangular prism with the entered dimensions.
  • The density is uniform across the order and matches the species and moisture condition.
  • The quantity includes every piece being transported.
  • The length is the actual length, not the nominal length before trimming.
  • Packaging, pallets, and fixings are excluded.
  • The result is an estimate; a weighbridge is the accurate check for a legal load.

Frequently asked questions

How much does a 2.4 m 100 × 50 mm timber weigh?

At 500 kg/m³ it weighs 6.00 kg. The same piece in a dense hardwood at 800 kg/m³ would weigh about 9.6 kg, so the species matters as much as the size.

What density should I use?

Use the air-dry density for the species from a reliable table, typically 350–550 kg/m³ for softwoods and 600–900 kg/m³ for hardwoods. If the timber is green or has been stored outside, use a higher figure or ask the supplier.

Does the calculator include the weight of treatment or paint?

No. Preservative treatment and paint add a small amount, usually far less than the moisture difference. If the load is near a limit, add a margin for coatings, straps, and packaging.

Can I use this for plywood or engineered wood?

The volume formula works for any rectangular panel or section, but the density must match the product. Plywood, MDF, and OSB have different densities from solid timber, so use the manufacturer's figure.

Why is the weight per metre different from the weight per piece?

Weight per metre is the weight of a one-metre length of the section. Multiply it by the piece length to get the weight per piece. It is a convenient way to estimate a run before the final cut list.

Is the estimate accurate enough for a vehicle load?

It is a planning estimate. Vehicle and trailer limits are legal limits, and enforcement uses a weighbridge. If the calculated load is close to the limit, weigh the vehicle or use the supplier's documented weights.

Sources

This is an educational weight estimate, not a load rating or transport approval. Species, moisture, and piece dimensions vary, and vehicle limits are legal limits. Confirm the weight with the supplier or a weighbridge before loading.

2026 update

How to use the professional output

This page is not just a formula box. The result is designed to be checked, compared, and taken away.

  • Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
  • A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
  • Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.

The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.

Calccc Editorial Team · Updated 2026-11-19

Prepared by Calccc Editorial Team as an educational estimate. This page is not a licensed professional review and is not financial, medical, legal, or tax advice.

Editorial estimate prepared by the Calccc Editorial Team; not a licensed professional review.