What this calculator does
Board feet are the standard way to price and compare lumber, especially hardwoods. A board foot is a volume, not a length, so a wide plank contains more board feet than a narrow one of the same length. This calculator turns nominal or actual dimensions into board feet per piece and a total for the whole order. Use actual measured thickness and width for the most accurate result, and remember that rough-sawn lumber is usually sold at its rough dimensions while surfaced lumber may be smaller.
How to use it
- Measure thickness and width in inches and length in feet.
- Enter the number of pieces you are pricing.
- Use actual dimensions for surfaced lumber, or nominal dimensions if that is how the price is quoted.
- Review board feet per piece and total board feet.
How it works
Example calculations
Example 1: one 1 x 6, 8 feet long
A 1-by-6 board 8 feet long is 1 x 6 x 8 / 12 = 4 board feet. One piece is 4 board feet, so the total is also 4.
Example 2: four 2 x 8s, 10 feet long
Each 2-by-8 at 10 feet is 2 x 8 x 10 / 12 = 13.33 board feet. Four pieces come to 53.33 board feet, or 4.44 cubic feet.
Example 3: ten 3/4 x 5-1/2 boards
A 0.75-by-5.5 board 6 feet long is 0.75 x 5.5 x 6 / 12 = 2.06 board feet. Ten pieces total 20.63 board feet. Using the actual width matters, because a nominal 6-inch width overstates the volume.
What the result means
Board feet measure volume, so the total rises with thickness, width, length, and quantity. Doubling the quantity or the width doubles the total. The formula uses inches for thickness and width and feet for length, which is why the divisor is 12. A 1-by-12 and a 2-by-6 of the same length contain the same board feet even though their shapes differ. When lumber is priced per board foot, compare that count with the price rather than the linear foot price. Surfaced lumber is often smaller than its nominal size, so measure the actual thickness and width. Board footage is a pricing unit, not a strength rating.
Common mistakes
- Using nominal thickness for surfaced lumber that measures smaller.
- Entering length in inches while the formula expects feet.
- Forgetting to multiply by the number of pieces.
- Dividing by 144 instead of 12 after mixing inches and feet.
- Mixing units, such as entering width in centimeters.
Assumptions and limits
- Thickness and width are entered in inches and length in feet.
- All pieces share the same dimensions and are counted by quantity.
- Actual measurements are used for surfaced lumber.
- No allowance is included for waste, trim, or defects.
- Each board is rectangular with square edges.
Frequently asked questions
What is a board foot?
A board foot is 144 cubic inches, equal to a piece 1 inch thick, 12 inches wide, and 12 inches long. It is a volume measure for any size.
Should I use nominal or actual dimensions?
Use actual dimensions when the price is based on the finished size, and nominal only if the seller quotes them that way. A nominal 2-by-4 measures 1-1/2 by 3-1/2 inches.
Why divide by 12?
Thickness and width are in inches, but length is in feet. Dividing by 12 converts inches to feet so the result is in board feet.
Does quantity change the board feet per piece?
No. Board feet per piece depends only on the dimensions. Quantity multiplies that figure to give the total.
How do I convert board feet to cubic feet?
Divide board feet by 12, because 12 board feet equal 1 cubic foot. For example, 53.33 board feet is about 4.44 cubic feet.
Do odd sizes like 3/4 inch work?
Yes. Enter decimals such as 0.75 for the thickness, and the formula handles fractional dimensions without any special steps.
Sources
2026 update
How to use the professional output
This page is not just a formula box. The result is designed to be checked, compared, and taken away.
- Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
- A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
- Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.
The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.
Go deeper
