Skip to content

Battery Charge Time Calculator

Enter the battery capacity, the current and target charge, and the charger's output. The calculator works out the milliamp-hours to add, adjusts for charging losses, and divides by the charger current to give hours and minutes. A 4,000 mAh battery going from 20% to 100% on a 2,000 mA charger takes about 1.88 hours.

Updated 2026-11-18 Editorial estimate Calccc Editorial Team Free · No sign-up
mAh
%
%
mA

Use the output printed on the charger, not the cable rating. A 20 W USB-C charger is often about 3,000-4,000 mA at 5 V.

Advanced options
%

Some energy is lost as heat. 80-90% is typical for a phone.

V

3.7 V for a single lithium phone cell, 5 V for USB power banks, 11.1 V for many laptop packs.

Scenarios A/BSave two input sets and compare the results. Stored only in this browser.
AEmpty
BEmpty

Your inputs stay in this browser. No account, no uploads.

Professional worksheet

Detailed schedule & assumptions

Inputs used, method, sensitivity, and any year-by-year table. The summary above stays compact; the audit lives here.

Professional worksheet

Inputs, scope, and sensitivity

Inputs used

Advanced inputs used

Method and scope

Result audit

MetricValue

What this calculator does

Charging time looks like a simple division: capacity divided by charger current. It is not, for three reasons. First, a battery is rarely empty, so only the missing share has to be replaced. Second, charging is not perfectly efficient; some of the energy from the wall becomes heat, so the charger must supply more than the battery receives. Third, and most important, real chargers taper. A phone may accept full power up to about 80%, then slow down to protect the cells, so the last stretch takes disproportionately long. This calculator gives the linear estimate, which is a good approximation for the middle of the range and a slight underestimate near 100%. The C-rate it reports is a useful sanity check: charging at more than about 1C, or one times the capacity in amp-hours, is hard on most lithium batteries.

How to use it

  1. Enter the battery capacity in mAh from the device specification.
  2. Set the current charge level and the level you want to reach.
  3. Enter the charger's output current in mA, not the cable rating.
  4. Keep the efficiency at about 85% for a phone unless you know otherwise.
  5. Use the C-rate to check that the charger is not oversized for the battery.

How it works

Charge time = capacity × (target − current) ÷ 100 ÷ (efficiency ÷ 100) ÷ charger current. In the default case: 4,000 × 80 ÷ 100 = 3,200 mAh to add; ÷ 85% = 3,765 mAh drawn; ÷ 2,000 mA = 1.88 hours.

Example calculations

Example 1: A phone from 20% to 100%

A 4,000 mAh battery needs 3,200 mAh to go from 20% to 100%. At 85% efficiency the charger supplies 3,765 mAh, which takes 1.88 hours at 2,000 mA. The charge rate is 0.50C.

Example 2: A partial top-up at a higher rate

A 5,000 mAh battery going from 5% to 80% needs 3,750 mAh. On a 3,000 mA charger that is 1.47 hours, or about 88 minutes, because the missing share is smaller even though the charger is faster.

Example 3: A power bank at 50%

A 10,000 mAh power bank half full needs 5,000 mAh. With 90% efficiency the wall draw is 5,556 mAh, giving 1.11 hours at 5,000 mA and adding 25.0 Wh to the battery.

What the result means

The linear estimate is most accurate in the middle of the charge range and least accurate at the very top. If the target is 100%, add a margin: the taper below 80% can add a third or more to the time the formula predicts. Screen use, cable resistance, and temperature all pull in the same direction, making the real charge slower rather than faster. The C-rate tells you how hard the battery is working: 0.5C means a two-hour charge, 1C means roughly an hour, and above 1C the battery heats more and ages faster. Fast charging is convenient but not free, and most phones deliberately limit it when the battery is warm or when the screen is on.

Common mistakes

  • Using the charger's wattage as if it were current, without converting by voltage.
  • Ignoring charging efficiency and assuming every milliamp from the wall reaches the battery.
  • Forgetting that charging slows dramatically above about 80%.
  • Charging through a poor cable that cannot carry the rated current.
  • Using the device while charging and wondering why the estimate is off.
  • Charging a battery at a C-rate far above what the manufacturer specifies.

Assumptions and limits

  • The charger delivers its rated current for the whole charge.
  • Battery capacity is the rated capacity, not the health-reduced capacity of an older cell.
  • Charging efficiency is constant, which is a simplification.
  • The device is idle and the screen is off during charging.
  • Temperature is within the range where the battery accepts a normal charge rate.

Frequently asked questions

Why does my phone charge more slowly above 80%?

Most phones taper the charge current near full to protect the battery and reduce heat. The last 20% can take as long as the first 60%, which the linear estimate does not capture.

What is a C-rate?

The charge or discharge current divided by the battery capacity in amp-hours. A 4,000 mAh battery charging at 4,000 mA is at 1C; at 2,000 mA it is at 0.5C.

Does a higher-wattage charger always charge faster?

Only if the device negotiates that power and the cable supports it. Many phones cap the accepted current, so a much larger charger may deliver no benefit and can add heat.

How much energy is lost during charging?

Typically 10 to 20 percent, mostly as heat. Wireless charging is usually less efficient than a cable, which is why the efficiency field matters for the time estimate.

Can I use this for a laptop?

Yes, if you enter the battery's mAh capacity and the charger current. Laptop packs often use higher voltages, so the watt-hour figure changes, but the time calculation is the same.

Is fast charging bad for battery life?

Faster charging produces more heat, and heat accelerates ageing. Occasional fast charging is fine, but keeping a battery cool and avoiding frequent charges at very high C-rates helps it last longer.

Sources

This is an educational estimate, not a specification for safe charging. Real charge time varies with the device's charging curve, temperature, cable, and battery health. Follow the manufacturer's charger and battery instructions, and do not exceed rated charge currents.

2026 update

How to use the professional output

This page is not just a formula box. The result is designed to be checked, compared, and taken away.

  • Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
  • A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
  • Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.

The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.

Calccc Editorial Team · Updated 2026-11-18

Prepared by Calccc Editorial Team as an educational estimate. This page is not a licensed professional review and is not financial, medical, legal, or tax advice.

Editorial estimate prepared by the Calccc Editorial Team; not a licensed professional review.