Skip to content

Health

One Rep Max Calculator

Enter a weight you lifted and the number of clean reps you completed. The calculator estimates your one-rep max with the Epley and Brzycki formulas and averages the two. It explains how training percentages relate to that estimate. These are mathematical estimates from one set, not a substitute for a supervised max test.

Updated 2026-11-12 Editorial estimate Calccc Editorial Team Free · No sign-up

Loading calculator…

What this calculator does

A one-rep max is the heaviest weight you can lift once with good form. Testing it directly is demanding and not always safe, so lifters estimate it from a set taken close to failure. Two classic formulas, Epley and Brzycki, turn a weight and rep count into an estimated max. The two usually agree closely at low rep counts and drift apart as reps climb. Use the average as a planning number and the gap between them as a reminder of how rough the estimate gets.

How to use it

  1. Enter the weight you lifted, in pounds or kilograms.
  2. Enter the number of full reps completed with good form.
  3. Read the Epley and Brzycki estimates and their average.
  4. Compare the two; a wide gap means a high rep count and a less reliable estimate.
  5. Use the average to set working weights at a percentage of your max.

How it works

Epley: 1RM = weight x (1 + reps / 30). Brzycki: 1RM = weight x 36 / (37 - reps). The average 1RM is the mean of the two results. Both formulas are fitted from rep-max data rather than derived from physiology. Percentage tables then scale the estimate: about 90% for a triple, 85% for five reps, and 75% for ten. The formulas are usually applied to sets of one to ten reps and become unreliable above that.

Example calculations

Example 1: 185 lb for 5 reps

Epley gives 185 x 1.167, or about 215.8 lb. Brzycki gives 185 x 36/32, or about 208.1 lb. The average is about 212 lb, which puts a working triple near 190 lb.

Example 2: 135 lb for 10 reps

Epley gives about 180 lb and Brzycki also gives about 180 lb, because the two formulas nearly cross at ten reps. The average is 180 lb. Ten reps sits at the edge of what these formulas handle well.

Example 3: 225 lb for 3 reps

Epley gives 225 x 1.1, or 247.5 lb. Brzycki gives 225 x 36/34, or about 238.2 lb, and the average is about 242.9 lb. The 9-lb gap shows how much the rep count shifts each model.

What the result means

Treat the result as a training tool, not a fact. The formulas assume a trained lifter, a set taken near failure, and consistent form. They ignore leverage, muscle fiber mix, and experience, so two lifters with the same numbers can test very differently. They are most reliable at low reps, which is why a heavy triple gives a tighter estimate than a set of fifteen. The percentage table is the practical payoff: if the average is 242 lb, a set of five at 85% means about 206 lb. Round to a loadable weight and let how the set feels override the number. A true max attempt belongs with a spotter, safety pins, and a full warm-up.

Common mistakes

  • Estimating from a set stopped well short of failure, which understates the max.
  • Using a high-rep set, where both formulas drift and the gap widens.
  • Counting partial reps or bouncing the weight to add reps.
  • Attempting a true max without a spotter, safety pins, or a warm-up.
  • Treating one estimate as fixed across lifts and training cycles.

Assumptions and limits

  • The set was taken close to technical failure with consistent form.
  • The rep count is between one and ten.
  • The weight is in the same unit throughout.
  • The lifter is trained in the movement being tested.
  • No wraps, assistive equipment, or help from a spotter changed the lift.

Frequently asked questions

Which formula is more accurate?

Neither is reliably better. Epley tends to run slightly higher at low reps, and the two converge near ten reps. The average is a reasonable compromise, but a properly tested max is the only direct measure.

Can I use this for any lift?

It is most often applied to the bench press, squat, and deadlift. It works less well for movements where reps are limited by technique or grip rather than by muscle fatigue.

Why do the two estimates differ?

Each formula was fitted to a different body of lifting data, so they weight the rep count differently. The gap grows as reps rise above about six.

Should I test my max instead?

A direct test is the only exact measure, but it carries injury risk and a fatigue cost. An estimate from a hard set of three to five reps is usually enough for planning a training block.

How often should I re-estimate?

Recheck after a training block, roughly every four to eight weeks, or when the same weight starts feeling easier for the same reps.

What percentage should I train at?

Common ranges are 70% to 80% for volume work, 80% to 90% for strength, and 90% and above for peaking. Start at the lower end, since the estimate itself can be off by several percent.

Sources

This calculator provides an estimate for training planning only and is not medical advice. A one-rep max attempt carries a risk of injury, and estimates can be off by several percent. They do not account for your health, technique, or training history. Consult a qualified coach or physician before maximal testing, especially if you have an injury or a medical condition.

2026 update

How to use the professional output

This page is not just a formula box. The result is designed to be checked, compared, and taken away.

  • Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
  • A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
  • Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.

The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.

Go deeper

Guides that explain the math

One-Rep Max: Estimates, Percentages, and Safety
Health

One-Rep Max: Estimates, Percentages, and Safety

Estimate your one-rep max from a set of reps using the Epley and Brzycki formulas. See worked examples, a percentage table, common mistakes, and how to test a true max safely.

8 min read

Calccc Editorial Team · Updated 2026-11-12

Prepared by Calccc Editorial Team as an educational estimate. This page is not a licensed professional review and is not financial, medical, legal, or tax advice.

Editorial estimate prepared by the Calccc Editorial Team; not a licensed professional review.