Key takeaways
- Board feet measure volume, not area.
- Use actual thickness and width for rough lumber.
- Nominal dimensions are larger than actual.
- Add waste for defects and cuts.
- Price per board foot makes comparison easier.
The formula
Board feet = T × W × L ÷ 144, with T and W in inches and L in inches. If length is in feet, use T × W × L(feet) ÷ 12. Example: a 1 in × 6 in × 8 ft board: 1 × 6 × 8 ÷ 12 = 4 board feet. A 2 in × 4 in × 10 ft board: 2 × 4 × 10 ÷ 12 = 6.67 board feet.
Nominal vs actual
A 2×4 is actually 1.5 in × 3.5 in. A 1×6 is actually 0.75 in × 5.5 in. For construction lumber, the nominal size is a label; for hardwood, the actual rough thickness and width are used. Read the seller’s measurement convention before calculating.
An example
Five boards, each 1 in thick, 6 in wide, 8 ft long. Each is 4 board feet; total 20 board feet. At $8 per board foot, the cost is $160. Add 15% for defects and cuts: 23 board feet, or $184.
What to compare
Compare the board-foot price, the actual dimensions, and the grade. A lower price per board foot may be a lower grade or a different moisture content. For a project, compare the total cost including waste, not only the price per board.
More examples
A 2 in × 6 in × 12 ft board: 2 × 6 × 12 ÷ 12 = 12 board feet. A 1 in × 4 in × 6 ft board: 1 × 4 × 6 ÷ 12 = 2 board feet. For 10 boards, multiply by 10. Keep the units consistent; length in feet uses ÷12, length in inches uses ÷144.
Hardwood grading
Hardwood is graded on the clear cuttings on one face. A higher grade has fewer defects and a higher price per board foot. The board-foot price is not comparable across grades without checking the grade and thickness.
What to compare
Compare the board-foot price, the actual dimensions, the grade, and the moisture content. A lower price per board foot may be a lower grade.
A project example
A tabletop uses five boards, each 2 in thick, 8 in wide, 6 ft long. Each board is 2 × 8 × 6 ÷ 12 = 8 board feet. Five boards are 40 board feet. At per board foot, the wood costs . Add 20% for defects and planing: 48 board feet, or .
Pricing comparison
Compare the price per board foot, the grade, and the actual dimensions. A board that is 1.5 in thick is not the same as a 2 in rough board. The board-foot price should use the actual thickness.
What to compare
Compare the total board feet, the waste, and the total cost. A lower price per board foot can be offset by a lower grade or more waste.
Hardwood example
A 4/4 board is nominally 1 in thick; a 8/4 board is 2 in. A 4/4 board 6 in wide and 8 ft long is 1 × 6 × 8 ÷ 12 = 4 board feet. A 8/4 board of the same width and length is 8 board feet. The thickness doubles the volume and the price.
What to compare
Compare the board feet, the actual thickness, the grade, and the price. A “cheap” board that is thinner or lower grade may not be cheaper per usable piece.
Example with mixed sizes
Four boards 1×6×8 ft: 4 × 4 = 16 board feet. Two boards 2×4×10 ft: each 6.67, total 13.33. Three boards 1×8×6 ft: each 4, total 12. Grand total 41.33 board feet. Add 15% waste: 47.5 board feet. At /board foot, .
What to compare
Compare the total board feet, waste, grade, and price per board foot.
Cost and waste
Multiply board feet by the price per board foot, then add waste. A 15% waste factor on 41.33 board feet is 6.2 extra board feet. The total cost is the usable wood plus the waste. For an expensive species, the waste cost can be significant.
What to compare
Compare the total board feet, waste, grade, and price. The lowest price per board foot is not always the lowest total cost.
Actual dimensions
A nominal 2×4 is 1.5 in × 3.5 in; a nominal 1×6 is 0.75 in × 5.5 in. Use actual dimensions for board feet. The difference is large enough to change the order.
What to compare
Compare the actual size, board feet, grade, and price.
What to compare
Compare the actual dimensions, board feet, grade, and total cost. A lower price per board foot can be offset by a lower grade or more waste.
Keep the board-foot calculation with the order.
Compare the actual dimensions, board feet, grade, and total cost before ordering the lumber.
Compare the actual dimensions, board feet, grade, and total cost before ordering the lumber, and add a waste factor for defects.
Use the actual thickness and width for rough lumber. A nominal 2×4 is 1.5 in × 3.5 in, and a nominal 1×6 is 0.75 in × 5.5 in. Using the nominal size overstates the board feet and the cost.
Frequently asked questions
What is a board foot?
144 cubic inches of wood, or a 12 in × 12 in × 1 in board.
Do I use nominal or actual dimensions?
Use actual dimensions for the calculation. Nominal sizes are labels and are larger than the actual lumber.
How much waste should I add?
10–20% for defects, cuts, and planing, depending on the grade and project.
Why is hardwood priced per board foot?
It measures volume and allows comparison across different thicknesses and widths.
Related guides
- Tile Calculator: Square Footage, Waste, and Box Count
- Rent Affordability: How Much Rent Can You Actually Afford?
- Weighted Grades: Where Your Course Grade Really Comes From
Further reading