Key takeaways
- Linear feet are not board feet.
- Nominal size differs from actual size.
- Add 10–15% waste for cuts.
- Framing spans depend on load and code.
- Compare the total cost, not only the unit price.
Linear vs board feet
A 2×4×8 ft is 8 linear feet and 5.33 board feet (1.5 × 3.5 × 8 ÷ 12 if using actual size, or 2 × 4 × 8 ÷ 12 = 5.33 if using nominal). The nominal calculation is conventional for pricing; the actual size matters for fit and insulation.
Framing example
A 16 ft wall with studs every 16 in needs about 13 studs (16 ft = 192 in; 192 ÷ 16 = 12 spaces, 13 studs), plus plates. Two top plates and one bottom plate add 48 linear feet. Add headers, cripples, and blocking. A simple wall can use 20–30% more lumber than the stud count suggests.
Waste
Framing waste is usually 10–15% for cuts, defects, and mistakes. A complex roof or a wall with many openings may need more. Order the longest lengths you can handle to reduce splices, but keep the waste factor.
Nominal vs actual
A nominal 2×4 is 1.5 in × 3.5 in; a nominal 2×6 is 1.5 in × 5.5 in; a nominal 4×4 is 3.5 in × 3.5 in. The nominal size is a label; the actual size is smaller. Use actual dimensions for fit, insulation, and board feet if the seller prices by actual volume.
What to compare
Compare the linear feet, board feet, grade, species, and total cost. A lower price per piece may be a lower grade or a shorter length.
A wall example
A 20 ft wall with studs at 16 in on center: 240 ÷ 16 = 15 spaces, so 16 studs. Add two top plates and one bottom plate: 3 × 20 = 60 linear feet. Add a header, cripples, and blocking. A 20 ft wall may use 20–25 pieces of lumber, depending on openings.
Board feet
A 2×4×8 ft is 5.33 board feet using nominal dimensions. Ten of them are 53.3 board feet. At per board foot, . Compare the actual size if the seller prices by actual volume.
What to compare
Compare the linear feet, board feet, grade, species, and total cost. A low price per piece can be a lower grade.
Framing extras
Headers over doors and windows, cripples above and below openings, and blocking between studs add lumber beyond the basic stud count. A wall with a large opening may need a doubled header and jack studs. Add 10–15% for these extras and cuts.
Moisture and grade
Framing lumber is graded for strength and appearance. A lower grade may have more knots and wane. For structural use, the grade and species must match the plan. Do not substitute a lower grade without approval.
What to compare
Compare the linear feet, board feet, grade, species, and total cost.
Ordering strategy
Order the longest lengths that fit the transport and the site. Fewer splices mean a stronger wall and less waste. Keep a cut list and mark each piece. Return unused, undamaged lumber if the supplier allows it.
What to compare
Compare the total linear feet, board feet, waste, grade, and delivery. A lower unit price can be offset by delivery or a lower grade.
A second wall example
A 12 ft wall at 16 in on center: 144 ÷ 16 = 9 spaces, 10 studs. Plates 3 × 12 = 36 linear feet. Add a header and cripples. A 12 ft wall may use 14–16 pieces. Ten walls of this size need 140–160 pieces, plus waste.
What to compare
Compare the linear feet, board feet, waste, and total cost.
What to compare
Compare the linear feet, board feet, waste, grade, species, and delivery. A lower price per piece can be a lower grade or a shorter length.
Keep the cut list with the order.
Return unused, undamaged lumber if the supplier allows it.
Delivery and storage
Lumber should be stored flat and off the ground. Wet lumber can warp; stickers between layers help air circulation. Order the longest lengths and keep the cut list. Check the delivery access and the weight of the bundle before it arrives.
What to compare
Compare the linear feet, board feet, waste, grade, species, and delivery cost.
Framing layout
Mark the stud locations on the plates before assembly. A 16 in on-center layout is common; 24 in is allowed for some non-bearing walls. Headers and jack studs add pieces. Check the plan and the local code for the span and grade.
What to compare
Compare the linear feet, board feet, waste, grade, and total cost.
Load and span
Joists and beams have span limits based on species, size, and load. A longer span may need a deeper member or an engineered beam. Do not size structural lumber by guesswork; use the span table or an engineer.
What to compare
Compare the linear feet, board feet, grade, species, and span requirements.
Check the span table before ordering the joists and beams.
Compare the span table with the actual joist size and species before ordering.
Compare the span requirements with the actual lumber grade before ordering.
Frequently asked questions
How do I calculate board feet?
Thickness × width × length ÷ 12 for length in feet, or ÷ 144 for length in inches.
How many studs are in a 16 ft wall?
About 13 studs at 16 in on center, plus plates and extras.
What is the difference between nominal and actual lumber?
Nominal is the label; actual is the finished size, which is smaller.
How much waste should I add?
10–15% for framing, more for complex layouts.
Related guides
- Fence Calculator: Posts, Rails, Pickets, and Concrete
- Drywall Calculator: Sheets, Joint Compound, and Waste
- Gravel Calculator: Cubic Yards, Tons, and Coverage
Further reading