The short answer: A unit conversion multiplies a measurement by a fraction that equals one — 25.4 mm per inch, 0.45359237 kg per pound, 3.785411784 L per US gallon — so the units cancel and the number changes while the quantity does not. Write the factor with the unit you are removing on the opposite side, keep full precision until the end, and round only the final answer.

Key takeaways

  • A conversion factor is a ratio equal to one. 25.4 mm ÷ 1 in is valid because both sides describe the same length.
  • Cancel units like algebra. If the unit you want to remove does not cancel, the factor is upside down.
  • Exact definitions do not limit precision. The inch, pound, and gallon are defined exactly; the measurement you start with does limit it.
  • Round once, at the end. Rounding every step compounds error.
  • Temperature is not a factor problem. It needs an offset, so it follows a different formula.

The factor-label method, step by step

Start with the value and its unit, then multiply by a fraction in which the unwanted unit sits in the denominator. Multiply numerators and denominators, cancel the repeated units, and simplify. Converting 65 miles per hour to meters per second takes two factors: 65 mi/h × 1,609.344 m/1 mi × 1 h/3,600 s = 29.0576 m/s. The miles cancel, the hours cancel, and meters per second remain.

The method scales to chains. To convert 3,000 feet to kilometers, go feet to meters (0.3048), then meters to kilometers (1/1,000): 3,000 × 0.3048 ÷ 1,000 = 0.9144 km. Each factor equals one, so the product equals one and the physical distance is unchanged. Only the label and the number move.

If the units refuse to cancel, the factor is inverted. That single check catches most conversion errors before any arithmetic is trusted. It also explains why memorizing “multiply or divide” is fragile: the correct operation depends on which unit you start from and which you want.

Where the factors come from

The SI is built on seven base units: the second, metre, kilogram, ampere, kelvin, mole, and candela. Since the 2019 redefinition, four of them are tied to fixed constants rather than physical artifacts: the kilogram to the Planck constant (6.62607015 × 10⁻³⁴ J s), the ampere to the elementary charge (1.602176634 × 10⁻¹⁹ C), the kelvin to the Boltzmann constant (1.380649 × 10⁻²³ J/K), and the mole to the Avogadro constant (6.02214076 × 10²³ mol⁻¹). The metre follows the speed of light (299,792,458 m/s) and the second follows the cesium-133 transition at 9,192,631,770 Hz.

Everyday imperial factors are exact by the 1959 international yard and pound agreement: 1 inch = 25.4 mm, 1 foot = 0.3048 m, 1 yard = 0.9144 m, 1 mile = 1,609.344 m, and 1 pound = 0.45359237 kg. Volume follows from the inch: 1 US gallon = 231 in³ = 3.785411784 L and 1 US fluid ounce = 29.5735295625 mL. Area does too: 1 acre is exactly 43,560 ft², or 4,046.8564224 m².

Because these are definitions, they carry unlimited significant figures. They never limit the precision of a result. The measured quantity does.

Exact factors, measured inputs

Keep the two ideas separate. “One pound is 0.45359237 kilograms” is exact. “The package weighs five pounds” is a measurement with a tolerance that may be grams or may be a fraction of an ounce. Converting five pounds yields 2.26796185 kg, but printing all those digits claims a precision the original value never had.

A workable rule is that the least precise input sets the output precision. A length recorded as 1.2 m has two significant figures; converting it to feet gives 3.9 ft, not 3.937007874 ft. If the input was 1.200 m, four significant figures are defensible. The digits after that are calculator output, not information.

There is a practical exception: intermediate values. Carry four or five digits through the calculation so rounding does not accumulate, then round the reported result to the precision the input supports.

Precision, rounding, and false accuracy

Round once. Chaining rounded results drifts: 1.0 inch to centimeters is 2.54 cm; rounded to 3 cm and converted back, it becomes 1.2 inches. Nothing was mismeasured, but the number moved because the rounding was applied twice.

Display precision is a design choice; accuracy is a claim about the world. A converter may show 29.0576046 m/s for 65 mph, but the honest report is about 29 m/s, because 65 has two significant figures. Similarly, a currency conversion should not show six decimals when the exchange rate itself is quoted to four.

For significant figures, count from the first non-zero digit. Leading zeros are placeholders, trailing zeros after a decimal point are significant, and trailing zeros in a whole number are ambiguous unless written in scientific notation or marked. 2,500 could mean two, three, or four significant figures; 2.500 × 10³ means four.

The units that cause the most errors

Mass versus weight. The kilogram measures mass. The pound is legally defined as 0.45359237 kg of mass, but in commerce “pounds” often means weight, and pound-force is a separate unit: 1 lbf = 4.4482216152605 N under standard gravity, 9.80665 m/s². Mixing lbm and lbf is a classic engineering error.

US versus imperial gallons. A US gallon is 3.785 L; an imperial gallon is 4.546 L, about 20% larger. British fuel economy figures in miles per gallon are almost always imperial, which flatters the number to a US reader.

Ounces. A mass ounce is 28.349523125 g. A US fluid ounce is 29.5735 mL and an imperial fluid ounce is 28.4131 mL. Mass ounces and fluid ounces are different dimensions; they only coincide for water, roughly, at room temperature.

Tons. A US short ton is 907.18474 kg, a long ton is 1,016.0469088 kg, and a metric tonne is 1,000 kg. Shipping, scrap, and freight quotes depend on which ton is meant.

Recipe volumes. A cup of flour is not eight ounces by weight. Density differs by ingredient, so volume-to-mass conversions need a density assumption.

Temperature is the exception

Most conversions are multiplicative. Temperature scales have different zero points, so converting requires an offset as well as a scale factor: °C = (°F − 32) × 5/9 and K = °C + 273.15. Multiplying a Fahrenheit value by 5/9 without subtracting 32 produces an answer that looks reasonable and is wrong. Treat temperature as its own procedure, never as a factor.

Worked examples

Wall area. 350 ft² × 0.09290304 = 32.52 m². Convert the measurement once, rather than converting each side of the room separately and introducing two roundings.

Tire pressure. 32 psi × 6.894757293 = 220.6 kPa. This is gauge pressure; absolute pressure adds atmospheric pressure, about 101.3 kPa.

Shipping weight. 22.5 kg ÷ 0.45359237 = 49.60 lb. A carrier that rounds up to the next pound bills 50 lb, which is a commercial rule, not a conversion error.

Speed. 100 km/h ÷ 1.609344 = 62.14 mph. In the other direction, 65 mph × 1.609344 = 104.6 km/h.

Cooking volume. 2 US cups × 236.5882365 = 473.18 mL. A metric cup is 250 mL, so the same “two cups” is 500 mL in a metric recipe, a 5.7% difference that matters in baking.

Checking a conversion without a calculator

Anchors catch gross errors: a meter is slightly longer than a yard, a kilogram is about 2.2 lb, a liter is a bit more than a quart, a kilometer is about 0.62 mile, and 1 m/s is 3.6 km/h. If a result is off by a factor of ten or a factor of two, an anchor will usually reveal it.

Check direction as well as size. Converting to a smaller unit should increase the number; converting to a larger unit should decrease it. If 5 miles becomes 3 km, the factor was upside down. If 5 miles becomes 8 km, the magnitude is plausible and the arithmetic is probably right.

Frequently asked questions

How do I convert units without a table?

Build the factor from definitions you know. An inch is 2.54 cm, a pound is 0.4536 kg, a gallon is 3.785 L. Divide when converting to a larger unit and multiply when converting to a smaller one, then check with an anchor.

Why is 1 kg equal to 2.20462 lb?

Because 1 lb is defined as 0.45359237 kg, so 1 kg is 1 ÷ 0.45359237 = 2.2046226 lb. The number is not arbitrary; it is the reciprocal of the definition.

Is a metric ton the same as a ton?

No. A metric tonne is 1,000 kg. A US short ton is 907.18474 kg and a UK long ton is 1,016.0469088 kg.

How many significant figures should a converted value keep?

No more than the least precise input. Carry extra digits through the arithmetic, then round the final result to match the measurement.

Can I convert temperature with a single factor?

No. Temperature needs a scale factor and an offset. Use °C = (°F − 32) × 5/9 and K = °C + 273.15.

Why do two converters give slightly different answers?

They usually differ in the factor’s precision or in where they round. Check whether the tool keeps full precision internally and rounds only the display.

Further reading

Keep exploring

Read next Hex to RGB: Color Codes, Channels, and Alpha A hex code is three base-16 channel values in one string. Learn how RR, GG, and BB become… Read next Density Conversion: kg/m³, g/cm³, and lb/ft³ Density is mass per volume, and the metric and imperial units are linked by exact factors. Learn the… Read next Base Conversion: Binary, Decimal, Hex, and Place Value Convert integers between binary, octal, decimal, and hexadecimal, with place-value arithmetic, direct bit grouping, exact limits, and the…

Decision path

Use this guide in a decision

Open Conversion Decision Center Open companion solver