What this calculator does
Loading a barbell is simple until the numbers stop matching the plates on the rack. A 100 kg target with a 20 kg bar is 40 kg per side, which is one 25 kg and one 15 kg plate in a competition set, but a gym with only 25, 20, 10, 5, 2.5, and 1.25 kg plates reaches the same weight another way. This calculator does the arithmetic, picks the largest plates first so the bar stays tidy, and shows the closest achievable total when the target cannot be made exactly. It also accounts for collars, which are easy to forget and can add a kilogram or more. The result is a loading plan, not a training programme: the right weight for a lift still depends on the athlete, the set, and the goal.
How to use it
- Enter the total weight you want on the bar, including the bar and collars.
- Select the bar weight; Olympic bars are usually 20 kg, women's bars 15 kg.
- Choose the plate set that matches the rack in front of you.
- Add the total weight of both collars if you use them.
- Read the per-side load and the plate list, then load both sides equally.
- Check the difference line if the target cannot be made exactly.
How it works
Example calculations
Example 1: 100 kg with a 20 kg bar
The side load is 40.00 kg, made up of 25 kg × 1, 15 kg × 1. The actual total is 100.0 kg, exactly on target. Load the same plates on both sides and add collars if your gym requires them.
Example 2: 142.5 kg with a gym plate set
With a 20 kg bar and a gym set that has no 15 kg plate, the side load is 61.25 kg. The calculator uses 25 kg × 2, 10 kg × 1, 1.25 kg × 1, for an actual total of 142.5 kg. The same weight with a competition set would use fewer plates, but the total is the same.
Example 3: 65 kg with a 15 kg bar and basic plates
A lighter bar changes the side load. The target is 65.0 kg, the bar is 15.0 kg, so each side needs 25.00 kg. The basic set gives 20 kg × 1, 5 kg × 1, for 65.0 kg total.
What the result means
The per-side figure is what you actually load, so it is the number to say out loud at the rack. The plate list is ordered from largest to smallest to keep the bar balanced and the sleeve tidy. If the difference line is not zero, the target is not achievable with the selected plates; the closest total may be slightly under or over. A small difference matters more at heavy loads, where a 1.25 kg plate per side is 2.5 kg on the bar. The calculator assumes plates are available in unlimited pairs and that the bar and collars weigh what you entered; in a busy gym, you may need to substitute and recalculate.
Common mistakes
- Forgetting to subtract the bar weight before dividing by two.
- Loading plates on one side only and counting the total twice.
- Ignoring collars, which add weight on both sides.
- Using a 15 kg women's bar but entering the 20 kg Olympic bar.
- Assuming a target is achievable when the smallest plate is 2.5 kg.
- Mixing kilogram and pound plates in the same calculation.
Assumptions and limits
- The bar weight is known and matches the bar on the rack.
- The selected plate set matches the plates actually available in pairs.
- Collars are counted separately and weigh what the user enters.
- The target is the total weight including the bar and collars.
- Plates can be loaded symmetrically on both sleeves.
- The calculation is a loading aid, not a lifting recommendation.
Frequently asked questions
Why is the load per side half of the target minus the bar?
Because the bar carries the same plates on both sides. Subtract the bar and collars from the total, then divide by two. The result is the weight of plates on each sleeve.
What if the target cannot be made exactly?
The calculator fills the side with the largest plates first and shows the closest achievable total and the difference. You can accept the nearest load or change the target to a weight the plates can make.
Do collars count in the total?
Yes, if you use them. A pair of collars can add 1–5 kg depending on the type. Enter the combined weight of both collars so the target matches what is actually on the bar.
Why does the plate list start with the largest plate?
Using the largest plates first minimizes the number of plates and keeps the bar balanced and tidy. The total is the same regardless of order, but fewer plates are easier to check and load.
Can I use this for dumbbells or machines?
The calculator is designed for a barbell with equal plates on each side. Dumbbells and machines have their own loading systems, so the per-side logic does not apply directly.
Is the calculator in kilograms only?
Yes. The plate sets are metric. If your gym uses pounds, convert the target to kilograms first or use a pound-based plate chart; do not mix the two in one calculation.
Sources
2026 update
How to use the professional output
This page is not just a formula box. The result is designed to be checked, compared, and taken away.
- Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
- A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
- Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.
The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.