Skip to content

Pool Water Turnover Calculator

Enter the pool shape and dimensions, the shallow and deep end depths, and the target turnover time. The calculator finds the volume and the flow rate that turns it over. An 8 m by 4 m pool with depths of 1.2 m and 1.8 m holds 48 m³, so a 6-hour turnover needs 8 m³/h, or about 133 litres per minute.

Updated 2026-11-19 Editorial estimate Calccc Editorial Team Free · No sign-up
m
m

Used for rectangular pools only.

m
m
hours

A common target is 6-8 hours for a residential pool.

Scenarios A/BSave two input sets and compare the results. Stored only in this browser.
AEmpty
BEmpty

Your inputs stay in this browser. No account, no uploads.

Professional worksheet

Detailed schedule & assumptions

Inputs used, method, sensitivity, and any year-by-year table. The summary above stays compact; the audit lives here.

Professional worksheet

Inputs, scope, and sensitivity

Inputs used

Method and scope

Result audit

MetricValue

What this calculator does

Turnover is the time it takes the pump to move the pool's full volume through the filter. It is the simplest way to compare a pump with a pool and to set a run time, although it is not the only measure of water quality. A residential pool is often designed for a six to eight hour turnover, while commercial pools and spas use shorter targets. The volume comes from the surface area and the average depth, and the flow rate follows from the volume and the target time. This calculator handles rectangular and round pools with a sloped floor and converts the result into litres per minute. It does not test water chemistry, size the filter, or account for the head loss of heaters, chlorinators, and long pipe runs, so the pump must still be checked against its curve at the real system head.

How to use it

  1. Choose the pool shape, rectangular or round.
  2. Enter the length, and the width for a rectangular pool.
  3. Enter the shallow and deep end depths.
  4. Enter the target turnover time in hours.
  5. Read the volume, the required flow, and the flow in litres per minute.
  6. Check the filter's maximum flow and the pump curve at the real head.

How it works

Average depth = (shallow depth + deep depth) / 2. Surface area = length × width for a rectangle, or π × (diameter / 2)² for a round pool. Volume (m³) = area × average depth. Required flow (m³/h) = volume / turnover hours. Flow (L/min) = flow (m³/h) × 1,000 / 60. In the default case: area = 8 × 4 = 32 m², average depth = 1.5 m, volume = 48 m³, flow = 48 / 6 = 8 m³/h = 133 L/min.

Example calculations

Example 1: A 6-hour turnover

An 8 m by 4 m pool with depths of 1.2 m and 1.8 m has an average depth of 1.5 m and a volume of 48 m³. A 6-hour turnover requires 8 m³/h, or about 133 L/min. A pump rated for that flow at the real system head will turn the water over in about six hours of running.

Example 2: An 8-hour turnover

The same pool on an 8-hour target needs only 6 m³/h, or 100 L/min. A smaller pump running longer uses less electricity per day in many cases, but it must still be able to lift water through the filter and any heater. Turnover targets are a design choice, not a fixed rule for every pool.

Example 3: A round pool

A round pool 5 m in diameter with a constant 1.2 m depth has an area of π × 2.5² = 19.6 m² and a volume of 23.6 m³. A 6-hour turnover needs about 3.9 m³/h, or 65 L/min. Round pools hold much less water than their footprint suggests, which is why the shape matters.

What the result means

Turnover tells you how often the whole volume passes through the filter, but water quality also depends on circulation patterns, sanitiser levels, filtration, and bather load. A pool with dead spots can have poor water quality even at a good turnover rate, so return placement and flow direction matter. The volume calculation is only as good as the depth measurement: a hopper bottom, a beach entry, or a spa bench changes the average depth, and the average of the shallow and deep ends is an approximation. The flow figure is the flow at the filter, not at the pump outlet, so use the pump curve at the actual head rather than the open-flow rating. For a commercial pool, the required turnover is usually set by local regulation.

Common mistakes

  • Using the open-flow pump rating instead of the flow at the real system head.
  • Averaging the shallow and deep depths on a pool with a large flat area at one depth.
  • Ignoring the volume of a spa, catch tank, or infinity edge.
  • Applying a residential turnover target to a commercial pool.
  • Forgetting that the filter has a maximum flow rate.
  • Assuming turnover alone guarantees clean water.

Assumptions and limits

  • The pool has a simple rectangular or circular shape.
  • The floor slopes evenly between the shallow and deep ends.
  • The water level is at the design depth.
  • The turnover target is a planning choice, not a code requirement.
  • Filter, heater, and pipe head losses are not modelled.
  • The result is a starting point for pump selection, not a design.

Frequently asked questions

What is a good turnover time for a pool?

Residential pools are often designed for six to eight hours. Commercial pools and spas usually need shorter times set by local regulation. The right target depends on bather load, volume, and the filtration system.

How do I calculate pool volume in litres?

Multiply the surface area by the average depth to get cubic metres, then multiply by 1,000 for litres. A pool 8 m by 4 m with an average depth of 1.5 m holds 48 m³, or 48,000 litres.

Does turnover time affect water clarity?

It helps, because more passes through the filter remove more particles, but circulation and sanitiser matter as much. A pool with poor circulation can stay cloudy even with a short turnover time.

How long should the pump run each day?

A common starting point is one full turnover per day, which for the default pool means about six hours. Some pools run longer in summer or with heavy use. The best schedule balances water quality with energy cost.

Can I use a variable-speed pump?

Yes, and they are often more efficient. Run at a lower speed for a longer time to achieve the same turnover, then use a higher speed only when needed for cleaning or backwashing. Check that the lower speed still meets the filter and heater requirements.

Why does the filter's maximum flow matter?

Pushing more water through a filter than its rating can damage the media and reduce filtration. The pump and filter must be matched, so check the filter's design flow before choosing a pump for the turnover target.

Sources

This calculator is an educational planning tool, not financial, legal, insurance, medical, or professional advice. Results depend on the inputs and on rules that vary by place and provider. Confirm important decisions with a qualified professional and the relevant documents.

2026 update

How to use the professional output

This page is not just a formula box. The result is designed to be checked, compared, and taken away.

  • Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
  • A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
  • Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.

The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.

Calccc Editorial Team · Updated 2026-11-19

Prepared by Calccc Editorial Team as an educational estimate. This page is not a licensed professional review and is not financial, medical, legal, or tax advice.

Editorial estimate prepared by the Calccc Editorial Team; not a licensed professional review.