What this calculator does
A storage water heater is sized by what it can deliver in the busiest hour, not by how many litres the tank holds. The first-hour rating combines the usable hot water in the tank with the water the element can reheat while the tank is being drawn down. That is why a small tank with a powerful element can outperform a larger tank with a weak one on a busy morning. This calculator estimates the recovery rate, the energy needed to heat the tank, and the first-hour rating, then compares it with the peak-hour demand. It is a planning estimate for a single tank in a dwelling. Mixing valves, recirculation lines, pipe heat loss, solar pre-heat, heat-pump behaviour, and fixture flow rates all affect real performance, and local plumbing codes govern the installation.
How to use it
- Enter the nominal tank volume in litres.
- Enter the heating element or heat pump output in kilowatts.
- Enter the incoming cold water temperature.
- Enter the stored water temperature set point.
- Estimate the busiest hour of hot water use in litres.
- Compare the first-hour rating with the peak demand and check the margin.
How it works
Example calculations
Example 1: A 200 litre tank with a 3 kW element
With a 50 °C rise, the element recovers about 51.6 L/h and the tank holds 140 L of usable hot water, so the first-hour rating is about 192 L. If the busiest hour uses 150 L, the margin is comfortable; if a large bath and two showers push demand to 250 L, the tank will run cool before the hour is out.
Example 2: A smaller tank with a stronger element
A 150 L tank with a 6 kW element has 105 L usable and recovers about 103 L/h at the same 50 °C rise, for a first-hour rating of about 208 L. The smaller tank can beat the larger one on a busy morning, but it has less buffer if several draws happen at once and the element cannot keep up.
Example 3: Colder incoming water
In winter, incoming water at 5 °C instead of 10 °C raises the temperature rise to 55 °C. The same 3 kW element now recovers about 47 L/h instead of 51.6, and the first-hour rating drops to about 187 L. Colder ground water is one reason a tank that performs well in summer can feel short in winter.
What the result means
Match the first-hour rating to the busiest hour, not to the number of bathrooms or the tank size alone. A household with a large bath, a rain shower, and a washing machine can draw more than 200 L in an hour, while a household with low-flow fixtures may need far less. Recovery rate is the other half of the equation: a tank that is too small but recovers quickly can work for spaced-out draws, while a large tank is better for simultaneous demand. The 70% usable factor is a planning approximation, not a guarantee. Real usable capacity depends on stratification, dip tube design, and the thermostat setting. Stored water at 60 °C or more also needs a mixing valve at the outlet in many installations, and the local code sets the requirements.
Common mistakes
- Sizing by tank volume alone instead of the first-hour rating.
- Ignoring the incoming cold water temperature in winter.
- Using the label power of a heat pump rather than its actual output.
- Forgetting simultaneous draws such as a shower, bath, and washing machine.
- Setting the tank temperature very high without a mixing valve.
- Assuming the rated recovery holds when the tank is partly empty and cold.
Assumptions and limits
- The tank is a single storage unit with one heating element or heat pump.
- The cold and hot water temperatures are constant during the hour.
- Usable hot water is about 70% of the nominal tank volume.
- The element runs continuously for the full hour.
- Pipe heat loss, mixing valves, and recirculation losses are excluded.
- The demand estimate covers the busiest hour of the day.
Frequently asked questions
What is a first-hour rating?
It is the amount of hot water a storage heater can deliver in the first hour of heavy use, combining the usable hot water in the tank with the water reheated during that hour. It is a better sizing measure than tank volume alone.
How much hot water does a shower use?
A standard shower head at about 9 L/min for eight minutes uses roughly 72 L of hot water, though the mix of hot and cold at the fixture means the draw from the tank is lower. Low-flow heads use considerably less.
Why does element power matter so much?
A stronger element reheats the tank faster, which raises the first-hour rating and shortens the wait after a big draw. The trade-off is a larger electrical circuit, so the available supply and the local code matter as much as the rating.
Is a bigger tank always better?
No. A bigger tank has more standby heat loss, takes longer to heat from cold, and costs more. A smaller tank with a strong element can be more efficient for spaced-out demand. Match the first-hour rating to the actual peak hour.
What temperature should the tank be set to?
Many installations store water at about 60 °C to limit bacterial growth in the tank, then use a mixing valve to deliver a safe temperature at the tap. The right settings depend on the system and local rules, so follow the manufacturer and the code.
Does this work for heat-pump water heaters?
Use the heat pump's actual heating output rather than its electrical input. Heat pumps recover more slowly than resistance elements, so the first-hour rating is lower even though running costs are usually lower.
Sources
2026 update
How to use the professional output
This page is not just a formula box. The result is designed to be checked, compared, and taken away.
- Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
- A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
- Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.
The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.