Skip to content

Pond Liner Calculator

Enter the pond's length, width, and maximum depth, the overlap you want at the edges, and how quickly the pump should turn the water over. The calculator adds the depth and overlap on both sides to size the flat liner, then reports the liner area, water volume, weight, and pump flow. For a 4.0 × 3.0 m pond that is 1.0 m deep, the liner needs to be 6.30 × 5.30 m.

Updated 2026-11-19 Editorial estimate Calccc Editorial Team Free · No sign-up
m
m
m

The deepest point, measured from the water line to the bottom.

m

Extra liner beyond the top edge, for anchoring under stones or turf.

How long the pump should take to circulate the whole pond once.

Scenarios A/BSave two input sets and compare the results. Stored only in this browser.
AEmpty
BEmpty

Your inputs stay in this browser. No account, no uploads.

Professional worksheet

Detailed schedule & assumptions

Inputs used, method, sensitivity, and any year-by-year table. The summary above stays compact; the audit lives here.

Professional worksheet

Inputs, scope, and sensitivity

Inputs used

Method and scope

Result audit

MetricValue

What this calculator does

A pond liner is sold as a flat sheet, but it has to cover a three-dimensional hole. The sheet runs down one side, across the bottom, and up the other side, so the depth is counted twice in each direction, and the edge needs extra material to anchor under stones or turf. That is why a 4.0 × 3.0 m pond does not take a 4.0 × 3.0 m liner. The water volume matters for a different reason: it sets the weight on the ground and the size of the pump and filter. This calculator handles both. It assumes straight sides and a flat bottom, which gives a conservative liner size; a pond with sloped or stepped sides needs less material but also holds less water than the box estimate. The pump figure is a turnover starting point, not a filtration design.

How to use it

  1. Measure the pond's maximum length and width at the water line.
  2. Measure the maximum depth from the water line to the lowest point.
  3. Add an overlap of at least 15 cm per side for anchoring.
  4. Choose a pump turnover time: 1 hour for koi, 2 hours for a general garden pond, 4 hours for a wildlife pond.
  5. Check the liner area and order the next standard size up.
  6. Confirm the water weight against the ground or deck loading.

How it works

Liner length = pond length + 2 × (depth + overlap); liner width = pond width + 2 × (depth + overlap). Volume = length × width × depth, and pump flow = volume ÷ turnover hours. For the default pond: 4.0 + 2 × (1.0 + 0.15) = 6.30 m long and 5.30 m wide, holding 12,000 L.

Example calculations

Example 1: A 4 × 3 m garden pond, 1 m deep

The liner needs to be 6.30 × 5.30 m, an area of 33.4 m². The pond holds 12.0 m³, or 12,000 litres, which weighs about 12.0 tonnes. A two-hour turnover needs a pump rated near 6,000 L/h.

Example 2: A 6 × 4 m pond, 1.5 m deep

Depth is expensive in liner: the sheet grows to 9.30 × 7.30 m and 67.9 m². The water volume jumps to 36,000 litres, or 36.0 m³. A four-hour turnover still needs about 9,000 L/h, which is why deeper ponds need larger filters and pumps.

Example 3: A small wildlife pond

A 2.0 × 1.5 m pond that is 0.6 m deep with a 20 cm overlap takes a 3.60 × 3.10 m liner and holds 1,800 litres. A one-hour turnover needs only 1,800 L/h, though a wildlife pond may need no pump at all.

What the result means

The liner size is driven more by depth than by surface area, because depth is added twice in each direction. Going from 1 m to 1.5 m deep adds a full metre to both the length and the width of the sheet, which is a large jump in cost. The volume drives the weight and the pump. A cubic metre of water is a tonne, so a 12.0 m³ pond is a 12.0 tonne load before rock, filtration, and the liner itself. Pump turnover is usually quoted as the time to circulate the whole volume once: one hour for heavy fish loads, two for a general garden pond, four for a lightly stocked wildlife pond. Head height, pipe friction, and filter resistance reduce real flow, so choose a pump rated above the calculated figure.

Common mistakes

  • Ordering a liner the same size as the pond surface and forgetting the sides.
  • Measuring depth from the ground rather than from the water line.
  • Forgetting the overlap needed to anchor the liner under stones or turf.
  • Sizing the pump from the surface area instead of the water volume.
  • Ignoring head height and pipe friction when choosing a pump.
  • Placing a large pond where the ground cannot carry the water weight.

Assumptions and limits

  • The pond has straight sides and a flat bottom.
  • Maximum depth is measured from the intended water line.
  • The overlap is applied on all four sides.
  • Water density is about 1 tonne per cubic metre, ignoring dissolved solids.
  • The pump turnover time is a design choice, not a guarantee of filtration.
  • Rock, substrate, and equipment displacement are not subtracted.

Frequently asked questions

How do I calculate pond liner size?

Add the depth and overlap twice to both the length and the width: liner = (length + 2 × (depth + overlap)) by (width + 2 × (depth + overlap)). For the default pond that gives 6.30 × 5.30 m.

How much overlap should a pond liner have?

At least 15 cm per side for a buried edge, and more if the edge is raised or the ground is uneven. The overlap is what lets you anchor the liner under stones or turf and allows for settling.

How much does a pond hold?

Volume = length × width × depth. The default 4.0 × 3.0 m pond at 1.0 m holds 12,000 litres, or 12.0 cubic metres. Sloped sides reduce the real volume.

What size pump do I need?

A common starting point is to circulate the whole volume every one to four hours, depending on the fish load. The default pond needs about 6,000 L/h for a two-hour turnover, but head height and filter resistance mean the rated flow should be higher.

Should I use a liner or a preformed pond?

A liner allows any shape and usually costs less for a large pond; a preformed shell is quicker and more durable for a small one. The trade-off is flexibility, weight, and the risk of punctures, so use a protective underlay with a liner.

How deep should a garden pond be?

Deeper water is more stable in temperature and safer for fish over winter, but it needs more liner and a stronger pump. A wildlife pond can be shallow with a deep section; a koi pond needs more depth and much more filtration.

Sources

This is an educational material estimate, not engineering or pond-design advice. Ground conditions, slopes, and local regulations vary, and a large pond may need structural or planning review. Check the load-bearing capacity and any permit requirements before digging.

2026 update

How to use the professional output

This page is not just a formula box. The result is designed to be checked, compared, and taken away.

  • Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
  • A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
  • Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.

The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.

Calccc Editorial Team · Updated 2026-11-19

Prepared by Calccc Editorial Team as an educational estimate. This page is not a licensed professional review and is not financial, medical, legal, or tax advice.

Editorial estimate prepared by the Calccc Editorial Team; not a licensed professional review.