Key takeaways
- The pascal is the hub. Every conversion runs value → Pa → target unit, so there are no pairwise factors to memorize.
- Bar and atm are close but not equal. 1 atm = 1.01325 bar, a 1.3% difference that matters in calibration and at depth.
- Psi is the US customary unit and equals 6,894.757 Pa, or about 6.895 kPa.
- Gauge pressure is not absolute pressure. A tyre gauge reading 32 psi is about 46.7 psi absolute at sea level.
- Weather hectopascals are kPa × 10. Standard sea-level pressure is 1013.25 hPa, 101.325 kPa, or 1 atm.
Pressure is force spread over an area
Pressure is force divided by the area over which it acts, and the SI unit is the pascal: 1 Pa = 1 N/m². The unit is coherent, meaning no extra factor appears when it is combined with newtons and square metres, which is why scientific and engineering work routes every other pressure unit through it. One pascal is small — a sheet of ordinary office paper lying flat exerts roughly 0.8 Pa — so everyday pressures are quoted in kilopascals, bar, or psi rather than in bare pascals.
The scale of common pressures is worth carrying in your head. Standard sea-level atmospheric pressure is about 101,325 Pa. A car tyre runs at roughly 220 kPa above ambient. A domestic water supply might be 300–400 kPa. A scuba cylinder is filled to about 200 bar, or 20,000 kPa. A laboratory vacuum chamber may sit at 1 Pa or lower. In each case the number is meaningful only with its unit, and the unit is chosen by industry convention as much as by the SI.
Because pressure is force over area, it is dimensionally identical to stress: the same pascal measures the stress in a steel beam and the pressure of gas in a pipe.
The four common units and their exact factors
The bar is defined as exactly 100,000 Pa, or 100 kPa. It is close to atmospheric pressure — close enough that many people use the two interchangeably — and it is the working unit in much European engineering, in some national weather services, and in scuba diving. The millibar is 100 Pa, so 1 bar = 1,000 mbar, and the hectopascal used in weather reports is exactly the same size as the millibar.
The standard atmosphere is defined as exactly 101,325 Pa. It is a defined reference value rather than a measured average, which is why it carries six significant figures. One atmosphere is 101.325 kPa, 1.01325 bar, and 14.6959 psi. The gap from one bar is 1.325 kPa, or about 1.3%.
The pound per square inch comes from the pound-force and the square inch: 4.4482216152605 N over 0.00064516 m², which is 6,894.757293168 Pa. That is 6.894757 kPa, 0.06894757 bar, and 0.06804596 atm. The reciprocals matter just as much: 1 atm = 14.6959488 psi, and 1 bar = 14.5037738 psi.
Other units turn up often enough to be worth knowing. One torr is 101,325/760 = 133.322 Pa. A conventional mercury column gives 1 mmHg = 133.3224 Pa and 1 inHg = 3,386.389 Pa, so 1 psi = 51.7149 torr. One kilogram-force per square centimetre is 98.0665 kPa, and one standard atmosphere is 760 torr by definition.
Converting through the pascal
Write each unit’s factor in pascals and the conversion becomes one multiplication and one division: from unit A to unit B, multiply by A’s factor and divide by B’s. Converting 32 psi to kilopascals: 32 × 6,894.757 = 220,632 Pa, which is 220.63 kPa, 2.2063 bar, and 2.1775 atm.
Two bar to psi: 2 × 100,000 = 200,000 Pa; divide by 6,894.757 to get 29.008 psi. The same 2 bar is 200 kPa and 1.9738 atm. A weather report of 1013.25 hPa is 101,325 Pa, which is exactly 1 atm, 1.01325 bar, and 14.6959 psi.
The chain also handles units the converter does not list. A blood pressure of 120/80 mmHg is 16.00/10.67 kPa, because each mmHg is 0.1333224 kPa. A 30 psi tyre is 206.84 kPa. A 100 psi air line is 689.48 kPa, 6.8948 bar, and 6.8046 atm. Checking one result in a second unit is usually enough to catch a slipped decimal point.
Where each unit is used in practice
Weather services report surface pressure in hectopascals, so a chart shows 1013 hPa for standard conditions and a deepening low at 985 hPa. US aviation still sets altimeters in inches of mercury, which is why a METAR reads 29.92 inHg for the standard atmosphere; 29.92 inHg is 1013.2 hPa. Tyre placards in the United States use psi, while European placards use bar or kPa, and a 32 psi tyre is 2.21 bar.
Diving works in bar because the pressure of ten metres of seawater is about one bar, so depth and pressure convert with a rule of thumb that is easy to check against a gauge. Medical blood pressure stays in mmHg, a legacy of the mercury manometer, and vacuum engineering uses torr, millibar, or pascal depending on the industry. The unit is a convention, and reading the datasheet’s unit before the number prevents most of the errors described below.
Gauge, absolute, and differential pressure
A gauge measures the difference between the pressure inside a system and the pressure of its surroundings, so a tyre gauge reading 32 psi means 32 psi above ambient. Absolute pressure adds the ambient pressure: at sea level, 32 psig is about 46.7 psia, and 2 barg is about 3.013 bara. The suffix carries the distinction — psig and barg are gauge, psia and bara are absolute — and dropping it is how reports become ambiguous.
This is the most common source of large errors in pressure work. A vacuum system quoted at −0.8 bar gauge sits near 0.2 bar absolute, not at a negative absolute pressure. A barometer reads absolute pressure while a boiler gauge reads gauge pressure, and the gauge value must be corrected before any thermodynamic calculation. Differential pressure, the difference between two points, is a third case and is exactly what a filter monitor or an orifice flow meter measures.
Where pressure conversions go wrong
Treating bar and atm as equal. The 1.3% difference is negligible on a weather map and significant in a calibration laboratory or at depth, where it compounds with every other approximation in the chain.
Mixing gauge and absolute readings. Adding 14.7 psi to a value that is already absolute, or forgetting to add it to one that is not, produces an error of about one whole atmosphere.
Confusing kPa with hPa. The factor is 10, so 1013.25 hPa is 101.325 kPa; moving the decimal the wrong way makes the pressure ten times too large. Likewise 1 MPa is 1,000 kPa, not 100.
Using the wrong mercury column. mmHg, cmHg, and inHg differ by factors of 10 and 25.4, and conventional values differ slightly from values at 0 °C or 60 °F. Mixing them is a quiet error because all three are casually described as mercury-column readings.
Assuming psi is metric. Psi is defined from the pound-force and the inch, both of which are themselves defined exactly in SI, so the factor is exact even though the unit is not metric.
Rounding and precision by context
Weather is reported in whole hectopascals, so 1013.25 hPa is published as 1013 hPa. Tyre pressures are given to the nearest psi or to 0.1 bar, and 1 psi is 6.9 kPa. Scuba tables work in whole bar or in 10 psi steps. Laboratory and calibration work should carry at least four significant figures and state the uncertainty, because the conversion factor is exact but the measurement is not.
Rounding too early is a real source of error. Converting 32 psi to 2.2 bar and then to 220 kPa loses about 0.6 kPa against the direct conversion. Round only the final displayed value and keep full precision in intermediate steps. When a specification reads “2 bar ± 0.1 bar”, convert the tolerance with the same factor rather than re-rounding the nominal value and guessing at the band.
Frequently asked questions
How many psi are in 1 bar?
14.5038 psi. One bar is 100,000 Pa and one psi is 6,894.757 Pa, so 100,000 ÷ 6,894.757 = 14.5037738.
How many kPa is 1 psi?
6.894757 kPa. Going the other way, 1 kPa = 0.145038 psi.
Is 1 bar the same as 1 atm?
No. 1 atm = 1.01325 bar, so 1 bar is about 98.7% of an atmosphere. The difference is 1.3%, which is small in weather reporting and not small in calibration.
What is the difference between psi and psig?
Psi is the unit; psig means psi gauge, measured relative to ambient pressure. Psia means psi absolute, measured from vacuum. A tyre at 32 psig is about 46.7 psia at sea level.
How do I convert mmHg to kPa?
Multiply by 0.1333224. So 120 mmHg is 16.00 kPa, and 80 mmHg is 10.67 kPa.
Why is standard atmospheric pressure 101,325 Pa?
It is a defined value adopted for reference, equal to 1,013,250 dyn/cm² in the older metric system, not a measured average of the real atmosphere.
Further reading
Keep exploring
Decision path