Skip to content

Everyday

Gravel Calculator

Enter the area length and width in feet, the gravel depth in inches, and the density in tons per cubic yard if you know it. The calculator returns square footage, cubic feet, cubic yards, and estimated tons. The default density of 1.4 tons per cubic yard suits common crushed stone.

Updated 2026-11-12 Editorial estimate Calccc Editorial Team Free · No sign-up

Loading calculator…

What this calculator does

Gravel, crushed stone, and similar aggregates are usually sold by the ton or by the cubic yard, while a driveway or path is measured in square feet and inches of depth. This calculator converts those measurements into volume and then into an estimated weight using a density you can change. Because a cubic yard of stone weighs roughly 1.2 to 1.7 tons depending on the material, the density field is the input to check first. Ask the supplier for the density of the specific product.

How to use it

  1. Measure the length and width of the area in feet.
  2. Enter the depth of gravel you plan to spread in inches.
  3. Enter the density in tons per cubic yard, or keep the default of 1.4.
  4. Review the area, cubic feet, cubic yards, and estimated tons.

How it works

Area = length (ft) x width (ft). Cubic feet = area x depth (in) / 12. Cubic yards = cubic feet / 27. Tons = cubic yards x density. For a 20-by-10-foot area at 3 inches and a density of 1.4, the volume is 50 cubic feet or 1.85 cubic yards, and the weight is 1.85 x 1.4 = 2.59 tons.

Example calculations

Example 1: 20 x 10 at 3 inches, density 1.4

The area is 200 square feet. At 3 inches deep the volume is 50 cubic feet, or 1.85 cubic yards. At 1.4 tons per cubic yard, the estimated weight is 2.59 tons.

Example 2: 12 x 12 at 2 inches

The area is 144 square feet. At 2 inches deep the volume is 24 cubic feet, or 0.89 cubic yards. At the same density, that is about 1.24 tons.

Example 3: 8 x 8 at 4 inches

The area is 64 square feet. At 4 inches deep the volume is about 21.33 cubic feet, or 0.79 cubic yards. At 1.4 tons per cubic yard, the estimate is 1.11 tons.

What the result means

The tonnage figure is only as good as the density you enter, because the volume math is fixed while weight per cubic yard is not. Crushed stone, pea gravel, and river rock pack differently, and damp material weighs more than dry material because water fills the spaces between pieces. A supplier who sells by the ton should be able to state the density for the product in stock. Ordering a little extra, often 5 to 10 percent, covers compaction, spreading loss, and low spots in the base. For a driveway, the compacted depth is what matters, so a loose layer starts thicker.

Common mistakes

  • Ordering tons when the supplier sells by volume, or the reverse.
  • Leaving the default density in place without checking the stone type.
  • Entering depth in feet instead of inches.
  • Skipping the extra allowance for compaction and spreading.
  • Measuring a sloped or irregular area as a simple rectangle.

Assumptions and limits

  • The area is rectangular and roughly level.
  • Depth is uniform across the area.
  • The density entered applies to the delivered, in-place material.
  • No compaction or waste allowance is included in the result.
  • Dimensions are in feet and depth is in inches.

Frequently asked questions

How many tons are in a cubic yard of gravel?

It depends on the stone. Crushed stone is about 1.4 tons per cubic yard, with a range of roughly 1.2 to 1.7. Ask your supplier for the product's density.

How much area does a cubic yard cover?

At 3 inches deep, a cubic yard covers about 108 square feet, at 2 inches about 162, and at 4 inches about 81.

Should I order extra gravel?

Yes, 5 to 10 percent is common. Extra material covers compaction, spillage, and low spots, and avoids a second delivery charge.

Does wet gravel weigh more?

Yes. Water adds weight, so damp stone can weigh more per cubic yard than dry stone. The supplier's density should reflect the material's condition.

What depth should a gravel driveway be?

A common range is 4 to 6 inches of compacted stone over a prepared base. Soil, drainage, and traffic loads can call for more, so check with a local contractor.

Can I use this calculator for sand or topsoil?

Yes. The volume math is the same, but change the density. Sand and topsoil weigh differently per cubic yard than crushed stone.

Sources

This calculator is a planning estimate only. Aggregate density, moisture, compaction, and supplier rounding all affect the delivered quantity and weight. Confirm the density and the unit of sale with your supplier before ordering.

2026 update

How to use the professional output

This page is not just a formula box. The result is designed to be checked, compared, and taken away.

  • Professional worksheet. The result includes the inputs used, the method and scope, and a one-variable sensitivity check for finance calculators.
  • A/B scenarios. Save two input sets in the browser and compare the primary, secondary, and breakdown figures side by side.
  • Print / PDF and CSV. Print a branded worksheet, or export the year-by-year table when the calculator produces one.

The formulas and assumptions above still govern the number. The worksheet makes the estimate auditable; it does not make it a lender quote, tax return, or personalized advice.

Go deeper

Guides that explain the math

Gravel Calculator: Cubic Yards, Tons, and Coverage
Everyday

Gravel Calculator: Cubic Yards, Tons, and Coverage

Estimate gravel volume, convert cubic yards to tons, and account for compaction and waste.

5 min read

Calccc Editorial Team · Updated 2026-11-12

Prepared by Calccc Editorial Team as an educational estimate. This page is not a licensed professional review and is not financial, medical, legal, or tax advice.

Editorial estimate prepared by the Calccc Editorial Team; not a licensed professional review.